manualshive.com logo in svg

Ryobi RLM46160S, Original Instructions Manual

Share
Download
Ryobi RLM46160S Original Instructions Manual Download Page 14

User Manual

12

MAINTENANCE SCHEDULE

Before   

each use

After 1st month 

or 20 hours of 

operation

Every 3 months 

or 50 hours of 

operation

Every 6 months 

or 100 hours  

of operation 

Every 12 months 

or after 300 

hours  

of operation

Check engine oil

n

Change engine oil

n

n

Check air filter

n

Clean air filter

n

Change air filter

n

Check/adjust spark plug

n

Replace spark plug

n

Check/adjust idle speed

n

Check/adjust valve  

clearance*

n

Clean fuel tank and filter*

n

Check fuel tube

n

Check for worn or  

damaged parts

n

Check all starting  

interlock and throttle 

lever for proper 

functionality

n

Check if the blade stop 

within 6 seconds after 

setting the throttle lever 

to the “Stop“ position 

(hard up against the top 

of the mower handles).

n

* These items should only be carried out by an authorised service center.

NOTE:

 Maintenance should be performed more frequently when the product is used in dusty areas.

 

When the engine has exceeded the maximum figures specified in the table, maintenance should still be cycled 

 according to the intervals of time or hours stated herein.

Summary of Contents for RLM46160S

















Reviews:

No comments

Brands by name

Popular brands

Load more brands