background image

2

 

Original instructions

 

| English

 

SPECIFIC SAFETY WARNINGS

 

Do not use the generator to provide power for 

emergency medical equipment or life support devices.

 

Exhaust fumes contains poisonous carbon monoxide, 

a colourless, odourless gas. Breathing exhaust fumes 

can cause loss of consciousness and can lead to death. 

If running in a confined or partially-enclosed area, 

the air may contain a dangerous amount of carbon 

monoxide. To keep exhaust fumes from building up, 

always provide adequate ventilation.

 

Locate the set in a convenient place, avoiding long 

extension leads and possible damage to leads by 

pedestrians or vehicular traffic.

 

Always use a battery-powered carbon monoxide 

detector when running the generator. If you begin to 

feel sick, dizzy, or weak while using the generator, shut 

it off and get to fresh air immediately. See a physician. 

You may have carbon monoxide poisoning.

 

Place the generator on a flat, stable surface with a 

slope of no more than 4°.

 

Operate outdoors in a well-ventilated, well-lit area 

isolated from working areas to avoid noise interference.

 

Operating the generator in wet conditions could result in 

electrocution. Keep the product dry.

 

Keep the generator a minimum of 1 m away from all 

types of combustible material.

 

Do not touch the muffler or cylinder during or 

immediately after use; they are hot and will cause burn 

injury.

 

Do not allow the generator’s gas tank to overflow when 

filling. Fill to 25 mm (1”) below the top neck of the gas 

tank to allow for fuel expansion. Do not cover the fuel 

tank cap when the engine is running. Covering the fuel 

tank cap during use may cause engine failure and/or 

damage to the product.

 

Allow the engine to remain in a shutdown condition for 

at least five minutes before adding unleaded fuel or oil.

 

Do not remove the oil dipstick or the fuel tank cap when 

the engine is running.

 

Pay close attention to all safety labels located on the 

generator.

 

The product operates best in temperatures between 

-5°C and 40°C with a relative humidity of 90% or less.

 

Operating voltage and frequency requirement of 

all electronic equipment should be checked prior to 

plugging them into this generator. 

 

Operation of the generator at altitudes above 1,000 

m may require retuning. Consult a qualified service 

technician.

 

The generating set must not be connected to other 

power sources except another RIG2000PCB with the 

RIGPC1000 parallel cable (sold separately).

 

Save these instructions. Refer to them frequently and 

use them to instruct others who may use the product. 

If you loan someone the product, loan them these 

instructions also.

TRANSPORTATION AND STORAGE

 

Place the engine choke/off selector knob in the "off" 

position.

 

Place the main on/off switch in the "off" position.

 

Make sure the engine and the exhaust of product has 

cooled down.

 

Keep the product level to prevent fuel spillage.

 

Do not drop or strike the product or place under heavy 

objects.

 

Store the product in a well-ventilated area with the fuel 

tank empty. Fuel should not be stored near the product.

 

Empty the fuel tank, place the main on/off switch in 

the "off" position and restrain the product from moving 

before transporting in a vehicle.

MAINTENANCE

 

 WARNING

When servicing, use only original replacement parts. 

Use of any other parts could create a hazard or cause 

product damage.

 

 WARNING

Service and maintenance require extreme care and 

knowledge and should be performed only by a qualified 

service technician. For service and repair, contact an 

authorised service centre. When servicing, use only 

original manufacturer’s replacement parts, accessories, 

and attachments.

 

Do not make adjustments and repairs not described in 

this manual. For other repairs, contact an authorised 

service centre.

 

Before performing any maintenance, stop the engine 

and ensure the engine choke/off selector knob is in the 

"off" position. Ensure the engine and exhaust of the 

product has cooled down. Failure to heed this warning 

could result in serious personal injury or could damage 

the product.

 

 WARNING

Protection switches are vital for safety and may only be 

replaced by an authorised service centre.

 

Keep the product in a clean and dry environment where 

it is not exposed to dust, dirt, moisture, or corrosive 

vapours. Do not allow the cooling air slots in the 

generator to become clogged with foreign material such 

as leaves, and snow.

 

Do not use a garden hose to clean the product. Water 

entering the fuel system or other internal parts of the 

product can cause problems that will decrease the life 

of the product.

Summary of Contents for RIG2000PCB

























Reviews: