Ryobi RHT3600, Original Instructions Manual, Page: 5 / 15

3
the unit, or during transportation.
Ŷ
For transportation, secure the machine against
movement or falling to prevent injury to persons or
damage to the machine.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service we suggest you return the
product to your nearest authorized service center for
repair. When servicing, use only identical replacement
parts.
WARNING
The blades are extremely sharp. To prevent personal
injury, exercise extreme caution when cleaning,
lubricating and fitting or removing the blade protector.
Ŷ
Remove the battery before adjusting, maintaining or
cleaning.
Ŷ
You may make adjustments and repairs described
here. For other repairs, contact the authorized service
agent.
Ŷ
After each use, clean the body and handles of the
product with a soft dry cloth.
Ŷ
After each use, clean the debris from the blades
with a stiff brush, and then carefully apply a rust
preventative lubricant before refitting the blade
protector. The manufacturer recommends you to use a
rust preventative and lubricant spray to apply an even
distribution and reduce the risk of personal injury from
contact with the blades. For information about suitable
spray product, check with your local authorised service
centre.
Ŷ
You may wish to lubricate the blades lightly before use,
if necessary, using the above method.
Ŷ
Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorized service
centre.
INTENDED USE
The product is only intended for use outdoors. For safety
reasons the product MUST be adequately controlled by
using two handed operation.
The product is designed for home or domestic use. It
is intended to cut and trim hedges, shrubs and similar
vegetation.
It should be used in dry, well illuminated conditions.
It is NOT intended to cut grass, trees or branches. It should
not be used for any other purpose than hedge trimming.
RESIDUAL RISK
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Ŷ
The blades cannot be guarded whilst cutting. Contact
with the blades can cause serious injury. Keep the
blade away from yourself and others. Cover it with the
blade protector whenever you are not cutting.
Ŷ
Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
Ŷ
Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
QXPEQHVV DQG EODQFKLQJ RI WKH ¿QJHUV XVXDOO\ DSSDUHQW
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices are
all thought to contribute to the development of the these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Ŷ
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
Ŷ
After each period of operation, exercise to increase
blood circulation.
Ŷ
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
DESCRIPTION
See page 6.
PARTS
1. Rear handle
2. Trigger
3. Trigger lock button
4. Front handle
5. Operator presence switch
6. Guard
7. HedgeSweep
TW debris sweeper
8. Blade
9. Blade cover