entering the product increases the risk of electric shock.
■
Do not use the product if it has been dropped or received a sharp
blow. A damaged product increases the risk of fire. Always inspect
the product for damages before use.
■
Remove the battery pack from the product when not in use.
■
Do not disassemble or modify the product. Electric shock hazard may
occur even when a battery is not installed. Any part that is damaged
should be properly repaired or replaced by an authorised service
centre.
■
To reduce the risk of injury, close supervision is necessary when the
product is used near children.
■
Store the product indoors and away from children.
■
Use caution when plugging or unplugging other devices into the
product. Do not force plugs into the product.
■
If the product is used in a manner not specified by the manufacturer,
the protection provided by this equipment may be impaired.
■
Do not overload the product. The product must be used for powering
devices less than the product rating.
■
Never block the air vents. Blocked vents may cause overheating. The
product automatically turns off when overheated.
■
Keep the product cool. Do not place the product near heat vents or
in direct sunlight.
■
Do not use the product around flammable fumes and gases, such as
in the bilge of a boat or near propane tanks.
■
Do not put foreign objects into the product.
■
Operate the product using only the AC power type listed in the
product specifications.
■
The product should never be hard-wired into a circuit.
■
Do not leave the product unattended during operation.
■
Operate the product only in temperatures between 0°C and 40°C.
■
Do not use the product to power life support devices or other medical
equipment.
■
Risk of electric shock. When using a grounded appliance, the product
does not provide an electrical path to earth ground. Do not power
devices that are damaged or with damaged or frayed power cords.
■
An internal cooling fan runs to regulate the product’s operating
temperature. Always wait for the fan to stop before disconnecting the
battery pack from the product.
■
Use RYOBI 36V battery packs only. Do not use battery packs from
other manufacturers.
■
Do not at any time, let brake fluids, gasoline, petroleum-based
products, penetrating oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken, or destroy plastic, which could
result in serious personal injury.
■
The light source of the product is not replaceable. When the light
source reaches its end of life, the product must be replaced.
KNOW YOUR PRODUCT
See illustration.
1.
Power / Light button
4. Wall hanger holes
2. Type A USB charging port
5. AC socket
3. Type C USB charging port
6. Light
SYMBOLS ON THE PRODUCT
Safety alert
Read the instructions carefully before starting the
product.
Remove the battery pack before starting any work on
the product.
Beware of electric shock hazard.
Do not expose to rain or damp conditions
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
Double insulation
Regulatory Compliance Mark (RCM). Product meets
applicable regulatory requirements.
Isolated inverter
F20A*2
Time-lag type fuse
Indoor use only
PRODUCT SPECIFICATIONS
Battery Inverter
Model
RBT36300
Supply
36 V DC, 12.5 A MAX, 450 W MAX
Output
230 V AC, 50 Hz, 300 VA
Type A USB
5 V DC max 3 A / 9 V DC max 2 A / 12 V DC max
1.5 A
Type C USB
5 V DC max 2 A / 9 V DC max 2 A / 12 V DC max 2 A
/ 20 V DC max 2 A
*The USB ports share internal circuitry. If two USB ports are in use at
the same time, the two USB ports supply 5 V output only.
Dimensions
140 mm x 75 mm x 80 mm
Weight
300 g
Compatible
battery packs
(not included)
BPL3620D, BPL3626, BPL3626D, BPL3626D2,
BPL3640, BPL3640D, BPL3640D2, BPL3650,
BPL3650D, BPL3650D2, BPL3660D, BPL3690D,
BPL3612D
Pure Sine Wave
RYOBI is a trade mark of Ryobi Limited,
and is used under license.
© 2020 Techtronic Cordless GP.
Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
099631004001-01
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
POWER BUTTON LED FUNCTIONS
LED indicator
Status
Troubleshooting
Green
The product is on.
Flashing red
The product is overloaded. 1. Press the
power/light button to remove the lock state. The LED indicator turns off.
2.
Disconnect all devices. Make sure that the battery is sufficiently charged.
3. Press the
power/light
button to turn on the AC socket.
4.
Reconnect all devices. If the LED indicator flashes red again, the devices exceed the
capacity of the product.
Red
The product is overheated. 1.
Disconnect all devices. Allow the product to cool down until the LED indicator flashes red.
2.
Briefly press the power/light button
to reset the product. When the LED indicator turns green,
reconnect the devices.
Flashing yellow
The battery charge is low. Remove and charge the battery.
Flashing red (3x) The battery charge is
insufficient.
Remove and charge the battery.
