4
properly repaired or replaced by an authorised service
centre.
Bring the product to an authorised service centre to
replace damaged or unreadable labels.
CLEARING A BLOCKAGE
To reduce the risk of injury associated with contacting
rotating parts, always stop the engine, and make sure all
moving parts have come to a complete stop.
Remove the blower tubes to inspect for blockage. Clear
the tubes if required.
Remove the debris collector bag. Check that the bag
adaptor is free from obstruction.
Inspect the opening to the fan enclosure and the tube to
the debris bag for evidence of a blockage. Keep fingers
away from the fan or mulching blades at all times.
Do not attempt to remove the fan or mulching blade. If it
is necessary to remove the fan or mulching blades, bring
the product to an authorised service centre.
Reinstall the tubes and the debris collector bag before
starting the product.
CLEANING THE AIR FILTER
See Figure 12 - 13.
A dirty air filter will cause starting difficulty, loss of
performance, and shorten the life span of the engine. Check
the air filter monthly. For best performance, replace the air
filter at least once a year.
Loosen the air filter cover by turning the knob
counterclockwise.
Remove the air filter.
Clean the foam filter element with warm soapy water.
Rinse and let dry.
NOTE:
If the foam filter element is damaged, it should be
replaced.
Apply a light coat of engine oil to the foam filter element,
then squeeze it out.
Reinstall the air filter.
NOTE:
Make sure the filter is seated properly inside the
cover. Installing the filter incorrectly will allow dirt to enter
the engine, causing rapid engine wear.
Reinstall the cover and tighten knob to secure.
CLEANING THE EXHAUST PORT, MUFFLER AND
SPARK ARRESTOR
NOTE:
Depending on the type of fuel used, the type and
amount of lubricant used, and/or your operating conditions, the
exhaust port, muffler, and/or spark arrestor screen may
become blocked with carbon deposits. If you notice a power
loss with your petrol powered product, you may need to
remove these deposits to restore performance. We highly
recommend that only qualified service technicians perform
this service.
The spark arrestor must be cleaned or replaced every 50
hours or yearly to ensure proper performance of your product.
Spark arrestors may be in different locations depending on
petrol. Remember to properly replace and tighten the
fuel cap.
Run the engine until it stops, this will remove all fuel that
could become stale and leave varnish and gum in the
fuel system.
If applicable, drain all lubricant from the engine into a
container approved for lubricant. Remember to properly
replace the lubricant cap.
Store the product in a cool, dry, and well-ventilated place
that is inaccessible to children. Keep away from corrosive
agents, such as garden chemicals and de-icing salts.
Do not store outdoors.
When transporting the product in a vehicle, secure it
against movement or falling to prevent injury to persons
or damage to the product.
Never transport the product while the engine is running.
Abide by all government and local regulations for the
safe storage and handling of petrol.
Short term (less than 1 month)
Stop the engine and allow the product to cool down
before storing or transporting.
Clean all foreign materials from the product.
Store the product in a cool, dry, and well-ventilated place
that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Do not store outdoors.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury and poor performance, and may void your
warranty.
WARNING
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician.
For service, bring the product to an authorised service
centre. When servicing, use only original replacement
parts.
Stop the engine, allow the product to cool down, and
make sure all moving parts have come to a complete
stop. Disconnect the spark plug boot before conducting
any maintenance or cleaning work.
You may make adjustments and repairs described in this
manual. For other repairs, contact an authorised service
centre.
After each use, clean the product with a soft, dry cloth.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure that the product is in safe
working condition. Any part that is damaged should be
