background image

17

TROUBLESHOOTING

Problem

Possible Cause

Solution

No spark.

No fuel.

Engine is flooded.

Starter rope pulls harder

now than when new.
Engine requires

approximately three minutes

to warm up.
Carburettor requires

adjustment.

Check oil fuel mixture.

Air filter is dirty.

Spark arrestor screen is

dirty.
Idle speed screw on

carburettor needs

adjustment.
Line is welded to itself.

Not enough line on spool.
Line is worn too short.

Line is tangled on spool.
Engine speed is too slow.
Screw threads are dirty or

damaged.

Check spark. Remove spark plug. Reattach the

spark plug cap and lay spark plug on metal cylinder.

Pull the starter rope and watch for spark at spark

plug tip. If there is no spark, repeat test with a new

spark plug.
Push primer bulb until bulb is full of fuel. If bulb does

not fill, primary fuel delivery system is blocked.

Contact a servicing dealer. If primer bulb fills, engine

may be flooded, proceed to next item.
Remove spark plug, turn machine so spark plug

hole is aimed at the ground. Move choke lever to

“OPEN” and pull starter cord 10 to 15 times. This

will clear excess fuel from engine. Clean and

reinstall spark plug. Pull starter three times with

choke lever at “OPEN”. If engine does not start,

move choke lever to “CLOSE” and repeat normal

starting procedure. If engine still fails to start, repeat

procedure with a new spark plug.
Contact a servicing dealer.

Allow engine to completely warm up. If engine does

not accelerate after three minutes, contact a

servicing dealer.
Contact a servicing dealer.

Use fresh fuel and the correct 2-cycle oil mix.

Clean air filter. Refer to “Replacing and Cleaning

Air Filter” earlier in this manual.
Contact a servicing dealer.

Turn idle speed screw clockwise to increase idle

speed.

Lubricate with silicone spray.

Install a new spool.
Pull lines while alternately pressing down on and

releasing spool retainer.
Remove line from spool and rewind.
Advance line at full throttle.
Clean threads and lubricate with grease.

Engine will not start

Engine starts but will not

accelerate

Engine starts but will only

run at high speed at half

choke
Engine does not reach

full speed and emits

excessive smoke

Engine starts, runs, and

accelerates but will not

idle
Line will not advance

when using the Line tap

system

Spool retainer hard to

turn when using Line tap

system

Summary of Contents for RBC-33





















Reviews: