Safety
1
SHOPLIGHT SAFETY WARNINGS
■
Know the product. Read user’s manual carefully.
Learn its applications and limitations as well as the
specific potential hazards related to the product.
■
Use only with recommended battery pack and
charger. Any attempt to use another battery pack
will cause damage to the product and could possibly
explode, cause a fire, or personal injury.
■
Do not direct the light beam at persons or animals
and do not stare into the light beam yourself (not
even from a distance). Staring into the light beam may
result in serious injury or vision loss.
■
Do not disassemble the product.
■
Do not place the product or battery pack near fire or
heat. This will reduce the risk of explosion and possible
injury.
■
Do not store the product in a damp or wet location,
or in a location where the temperature may reach
or exceed 40°C (104°F). For example, inside sheds,
vehicles, or metal buildings in the summer.
■
Check damaged parts. Before further use of the
product, a part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Do not use the product if
it does not function properly.
■
Have the product repaired by a qualified person.
The product is in accordance with the relevant safety
requirements. Repairs should only be carried out by
qualified person using original spare parts, otherwise
this may result in considerable danger to the user.
■
The product is designed to operate in one mode
only. Do not connect to AC power and place the battery
in the battery port at the same time. Failure to follow this
rule will result in serious personal injury.
BATTERY SAFETY WARNINGS
■
Do not place battery tools or their batteries near
fire or heat. Following this rule will reduce the risk of
explosion and possibly injury.
■
Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
■
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
■
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
■
Do not place batteries near fire or heat. They may
explode.
■
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
■
For best results, your battery tool should be
charged in a location where the temperature is
more than 10°C but less than 38°C. Do not store
outside or in vehicles.
■
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with soap
and water. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
INTENDED USE
■
The product is intended to be used for general lighting,
such as:
–
vehicle maintenance
–
workbench illumination
–
camping illumination
–
reading light
–
wall illumination when painting
MAINTENANCE
■
When servicing, use only original Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
■
Do not attempt to modify the product or create
accessories not recommended for use with the product
by the manufacturer.
■
Over time, the pivot bushing may loosen up. If so,
tighten it with a slot screwdriver or coin.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOLS
Safety alert
Regulatory Compliance Mark (RCM).
Product meets applicable regulatory
requirements.
CE conformity
Please read the instructions carefully
before starting the machine.
Class II, double insulated
Summary of Contents for R18HS
