Ryobi R1801M, Operator'S Manual

Page: 3 / 20

3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions.
Failure to
follow all instructions listed below, may result in elec-
tric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
I
Keep your work area clean and well lit.
Cluttered
benches and dark areas invite accidents.
I
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust.
Power tools create sparks
which may ignite the dust or fumes.
I
Keep bystanders, children, and visitors away while
operating a power tool.
Distractions can cause you to
lose control.
ELECTRICAL SAFETY
I
Double insulated tools are equipped with a polar-
ized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug
in any way.
Double insulation eliminates the need
for the three-wire grounded power cord and grounded
power supply system.
I
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators.
There is an
increased risk of electric shock if your body is grounded.
I
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
I
Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately.
Damaged cords
increase the risk of electric shock.
I
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”.
These cords are
rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
I
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication.
A moment of inatten-
tion while operating power tools may result in serious
personal injury.
I
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts.
Loose clothes,
jewelry, or long hair can be caught in moving parts.
I
Avoid accidental starting. Be sure switch is off before
plugging in.
Carrying tools with your finger on the switch or
plugging in tools that have the switch on, invites accidents.
I
Remove adjusting keys or wrenches before turning
the tool on.
A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
I
Do not overreach. Keep proper footing and balance
at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
I
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
I
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of
the tool in unexpected situations.
I
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be
drawn into air vents.
TOOL USE AND CARE
I
Use clamps or other practical way to secure and
support the workpiece to a stable platform.
Holding
the work by hand or against your body is unstable and
may lead to loss of control.
I
Do not force tool. Use the correct tool for your
application.
The correct tool will do the job better and
safer at the rate for which it is designed.
I
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
I
Disconnect the plug from power source before
making any adjustments, changing accessories, or
storing the tool.
Such preventive safety measures
reduce the risk of starting the tool accidentally.
I
Store idle tools out of the reach of children and other
untrained persons.
Tools are dangerous in the hands of
untrained users.
I
Maintain tools with care. Keep cutting tools sharp
and clean.
Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
I
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using.
Many accidents are caused by
poorly maintained tools.
I
Use only accessories that are recommended by the
manufacturer for your model.
Accessories that may
be suitable for one tool, may become hazardous when
used on another tool.
I
Keep the tool and its handle dry, clean and free
from oil and grease.
Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean your
tool. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.