background image

Page 2

Table of Contents ............................................................................................................... 2

Accessories ........................................................................................................................ 2

 Unpacking .......................................................................................................................... 2

Rules For Safe Operation ............................................................................................... 3-5

A. Important Safety Rules For Battery Tools ................................................................... 4

B. Important Safety Instructions For Charger .................................................................. 4

C. Important Safety Instructions For Circular Saws ......................................................... 5

Features .......................................................................................................................... 6-7

Operation ...................................................................................................................... 8-18

Maintenance ..................................................................................................................... 19

Battery Pack Removal and Preparation For Recycling ..................................................... 19

Parts Ordering / Service ................................................................................................... 20

Look for this symbol to point out important safety precautions. It means attention!!!
Your safety is involved.

TABLE OF CONTENTS

The following recommended accessories are current and were available at the time this manual was printed.

5-1/2 in. (140 mm) Thin Kerf Blade

ACCESSORIES

Your circular saw has been shipped completely assembled
except for the blade. Inspect it carefully to make sure no
breakage or damage has occurred during shipping. If any
parts are damaged or missing, contact your nearest Ryobi
Authorized Service Center to obtain replacement parts before
attempting to operate saw. A blade, blade wrench, and this
operator's manual are also included.

UNPACKING

WARNING:

If any parts are missing, do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.

The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields.

WARNING:

Summary of Contents for R10630























Reviews: