background image

English

SYMBOLS

SYMBOLS

NAME

Safety Alert Symbol

Important:

Some of the following symbols may be used on your tool. Please study them and learn their meaning. 

Proper interpretation of these symbols will allow you to operate the tool better and safer.

Read Your Operator's Manual

Wear eye and hearing protection

Keep bystanders away

Ricochet

No blade.

RPM Decal

Boots

Gloves

No Smoking

Petrol

Oil

Mix Petrol and Oil

Switch

EXPLANATION

Wear eye and

 hearing

 protection when operating this

equipment.

Keep all bystanders at least 15m (50 ft) away.

Danger of Ricochet.

Do not install any type of blade on this unit.

Rotational direction and maximum speed of the shaft for the

cutting attachment.

Wear non-slip safety footwear when using this equipment.

Wear non-slip, heavy-duty gloves.

Do not smoke when mixing fuel or filling fuel tank.

Use unleaded petrol intended for motor vehicle use with an 

octane rarting of 87([R+M]/2) or higher.

Use synthetic 2-

stroke

 oil for air cooled engines.

Mix the fuel mix thoroughly and also each time before 

refuelling.
On/Off Switch

    = ON to Run

O = OFF to Stop

Your manual contains special messages to bring attention to

potential safety concerns as well as operating and servicing

information. Please read all the information carefully to ensure

satification and safe use.

Indicates danger, warning or caution. it means attention!!!

Your safety is involved.

Fully press and release the prime bulb 8 times.

Conforms to all regulatory standards in the country in the EU 

where the product is purchased.

- 1 -

Summary of Contents for PLT-3043YW















Reviews: