manualshive.com logo in svg

Ryobi OLT1833BL, Original Instructions Manual, Page: 22 / 24

Share
Download
Ryobi OLT1833BL Original Instructions Manual Download Page 22

PRODUCT SPECIFICATIONS

Cordless Line Trimmer / Edge Trimmer

Model

RLT1833BL4 / OLT1833BL

Voltage

18 V

No-load speed

High speed

0–6200/min

Low speed

0–5200/min

Cutting capacity

28 cm / 33 cm

Cutting line diameter

2.0 mm

Weight without battery pack

3.3 kg

Weight with heaviest battery pack

4.5 kg

Cutting width

280/330 mm

Noise emission values determined according to IEC 60335-2-91

A-weighted sound pressure level

L

pA

 = 84.3 dB

Uncertainty

K = 2.5 dB

A-weighted sound power level

L

WA

 = 95.7

Uncertainty

K = 2.5 dB

Vibration total values determined according to IEC 60335-2-91

Vibration emission value

Front handle

a

h

 = 3.9 m/s²

Rear handle

a

h

 = 4.7 m/s²

Uncertainty 

K = 1.5 m/s²

BATTERY AND CHARGER

Model

RLT1833BL4

OLT1833BL

Battery pack

RB18L40

—

Charger

RC18120 

—

Compatible 

battery packs

RB18L13, RB18L15, RB18L20, RB18L25, 

RB18L26, RB18L40, RB18L20A, RB18L50, 

RB18L60A, RB18L90A

Compatible 

chargers

RC18120, BCL1418H, BCL14183H, 

BCL1418IV*, RC18150U, BCS618G, 

RC18627U, RC18115

*BCL1418IV  is  compatible  for  charging  in  vehicles  with  12  V  DC 

outlets.

REPLACEMENT PARTS

Replacement head

RAC1214

Replacement bump knob

530455007

Replacement 2.0 mm trimming line

PWFTL2050T

VIBRATION LEVEL

 WARNING

The declared vibration value has been measured with a 

standard test method and may be used to compare one 

tool with another.
The declared vibration value may be used in a 

preliminary assessment of exposure.
The vibration emission during actual use of power tool 

can differ from the declared total value depending on the 

ways in which the tool is used.
Identify safety measures to protect yourself based on an 

estimation of exposure in the actual conditions of use, 

taking account of all parts of the operating cycle such 

as the times when the tool is switched off and when it is 

running idle in addition to the trigger time.

Summary of Contents for OLT1833BL

























Reviews:

No comments