background image

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.
1.  The warranty period is 24 months for consumers and commences on the date the product was purchased. This 

date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to 
consumer and private use only. So there is no warranty provided in case of professional or commercial use. This 
warranty applies only on new products.

2.  There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period 

described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended 
warranty is  clearly displayed in stores and / or on packaging and is contained within the product documentation. 
The end user is required to register his/her newly-acquired products online within 30 days from the date of 
purchase. The end user may register for the extended warranty in his/her country of residence if listed on the 
online registration form where this option is valid. Furthermore, end users must give their consent to the storage 
of their personal data that is required to be entered online. They must also accept the terms and conditions. 

7KHUHJLVWUDWLRQFRQ¿UPDWLRQUHFHLSWZKLFKLVVHQWRXWE\HPDLODQGWKHRULJLQDOLQYRLFHVKRZLQJWKHGDWHRI

purchase will serve as proof of the extended warranty.

3.  The warranty covers all defects of the product during the warranty period due to faults in workmanship or 

material at the purchase date. The warranty is limited to repair and/or replacement and does not include any 
other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the 
product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power 
supply. This warranty does not apply to:

 

any damage to the product that is the result of improper or lack of maintenance

 

any product that has been altered or modified

 

any product where original identification (trade mark, serial number) markings have been defaced, altered 

or removed

 

any damage caused by non-observance of the instruction manual

 

any product not displaying the CE approval mark on the rating plate 

 

any product that has been attempted to be repaired by a non-authorised warranty service centre or without 

prior authorisation by Techtronic Industries

 

any product connected to an improper power supply (amps, voltage, frequency)

 

any damage caused by external influences (water, chemical, physical, shocks) or foreign substances

 

normal wear and tear spare parts

 

inappropriate use, overloading of the tool

 

use of non-approved accessories or parts

 

Power tool accessories provided with the tool or purchased separately. including but not limited to screw 

driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide etc.

 

Components (parts and accessories) subject to natural wear and tear, including but not limited to Service 

& Maintenance Kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, 

auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench 

pins & springs, etc.

4.  For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country 

in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send 
the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product 
should be safely packed without any dangerous contents such as petrol, marked with sender’s address and 
accompanied by a short description of the fault.

5.  A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of 

the warranty period. Exchanged parts or products become our property. In some countries delivery charges or 
postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain 
unaffected.

6.  This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and 

Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty 
applies.

Summary of Contents for LLCDI1802

















Reviews: