![background image](http://html1.mh-extra.com/html/ryobi/eos-2410n/eos-2410n_user-manual_1506214013.webp)
DESCRIPTION
1.
Switch
2.
Paper clamp
3.
Cushion
4.
Tab
5.
Lever
6.
Dust bag frame
7.
Dust bag
8.
Paper punch
9.
Platen
10. Non-adhesive sandpaper
11. Live Tool Indicator
FEATURES
Your sander is suitable for sanding with coarse, medium,
and fine grit sandpaper. It will produce a fine scratch free
finish when used to sand with the grain on wood surfaces.
It has been designed so that flush corner sanding on
three sides of the sander is possible.
Your sander has a comfortable palm grip handle that
provides maximum one-hand comfort, and reduces
operator fatigue during continuous sanding operations.
Your sander also has a built in dust collection that
collects dust through punched holes in the sandpaper
and cushion (Fig. 5).
Before attempting to use your sander, familiarize
yourself with all operating features and safety
requirements.
SWITCH (1)
This tool is equipped with a simple switch control. To turn
the sander "
ON
", slide the switch to the left.
Slide the switch to the right to turn the sander "
OFF
".
WARNING
Do not allow familiarity with your sander to make
you careless. Remember, a careless fraction of a
second is sufficient to inflict severe injury.
OPERATION
WARNING
Your sander should never be connected to power
supply when you are assembling parts, making
adjustments, assembling or replacing sandpaper,
cleaning, or when not in use. Disconnecting
sander will prevent accidental starting that could
cause serious personal injury.
INSTALLING NON-ADHESIVE SANDPAPER
(Fig. 5)
Inspect sandpaper before installing.
DO NOT use
broken or defective sandpaper.
■
Unplug your sander.
WARNING
Failure to unplug your sander could result in
accidental starting causing possible serious
personal injury.
■
If replacing sandpaper, remove old sandpaper.
To remove paper, release paper clamp by lifting up on
lever, and disengaging it from the tab, and allowing
the lever to lower.
■
Insert end of new 1/4 sheet sandpaper approximately
1/2 in. (12.7 mm) under the paper clamp.
Note:
1/2 in. (12.7 mm) clamping of sandpaper is
necessary for multi-sheet stacking of paper.
■
Lift up on lever and lock into place. Apply downward
pressure to conform sandpaper to plate.
■
Wrap sandpaper around cushion. Lift lever on
opposite end of sander and insert loose end of
sandpaper under paper clamp. Fit sandpaper tight
against cushion.
■
Lift up on lever and lock into place.
■
Multiple sheets of sandpaper can be installed at one
time for convenience.
ATTACHING ADHESIVE (HOOK & LOOP)
SANDPAPER (Fig. 5)
■
Unplug the sander.
■
Align holes in hook and loop type sanding paper with
holes in pad, then carefully press fuzzy side of
sanding paper against pad as tightly as possible.
Note:
Hook and loop type sanding papers can be
reused for the life of the sanding abrasive. It is
recommended that you keep the sanding paper
backing pad clean to provide for best adhesion. Clean
occasionally by brushing lightly with a small brush.
PAPER PUNCH (Fig. 6)
A paper punch template has been supplied with your
sander for aligning and punching holes in sandpaper.
The punched holes must align with the holes in the
sander cushion.
■
Install sandpaper on your sander.
■
Align sander cushion over the paper punch.
■
Push down on sander
9
GB
English
F
D
E
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
PL
RO
SLO
TR
HR
EOS-2410N_20 lgs-10AUG06 8/10/03 4:12 PM Page 9