Ryobi EBW4023L Owner'S Operation Manual Download

Page: 15 / 17

Page 14

Change batteries of Laser (Fig. 21

)

Turn Off the Band Saw and switch off the laser beam.
Open the Laser Switch Box Cover by using Philip Head

Screw Driver to loosen that M3 Tappping Screw (59)

(see Fig. 20)
Replace the 2x Button Cell (AG13 or LR44 or SR44)

into the Button Cell Protection Tube (61). (see Fig. 21)
Close the Laser Switch Box Cover (58) and tighten the

M3 Tapping Screw (59). (see Fig. 20)
Switch on the laser beam and turn on the Band Saw for

cut operation.

Use only correct batteries Button Cell. (see Fig. 21)

MOTOR / ELECTRICAL

BRUSHES

(

Fig. 17)

To prevent accidental starting that could cause possible

serious personal injury, turn off the saw, and unplug thesaw

before working on the band saw.

Remove the screw (48) and washer (20), then pull the

brush (46) off.

Place the new brush in the groove with the plastic tabs

under the saw housing.
Retighten using the washer and screw.

WARNING:

BLADE

UIDES (Fig. 12)

Blade guides may become rounded and worn during use.

Remove the blade guides and file or grind flat.

Replace blade guides when filing or grinding has worn

them down and they can no longer be properly secured in

place.

WARNING:

Frequently vacuum or blow out sawdust from the motor.

If the power cord is worn, cut or damaged in any way, have

it replaced immediately by a qualified service technician.

Failure to do so could result in serious personal injury.

To avoid fire or electrocution, reassemble electric parts

with only identical Ryobi replacement parts.Reassemble

exactly as originally assembled.

There is a brush (46) located inside the saw housing, next

to the lower wheel( 29). It helps to protect the tire(47) and

wheel by brushing off saw dust. As the brush becomes

worn out, it will need to be adjusted or replaced.

WARNING:

DRIVE BELT (Fig. 18&19)

To prevent accidental starting that could cause possible

serious personal injury, turn off the saw, and unplug the

saw before working on the band saw.

Due to wear or breakage,the drive belt may need to be

replaced. The drive belt (53) is located behind the lower

wheel (50) of the band saw.
Remove the saw blade and set it aside. See section on

installing and Adjusting the Blade.
Pull the lower wheel away from the saw housing.
Remove the worn drive belt.
Place new drive belt on the pulley. As you slide the pulley

shaft (51) back into the hole in the saw housing, place

the drive belt over the motor pulley (52)

Replace the nut and washer on the pulley shaft and

retighten.
Replace saw blade.
Check thrust bearings and blade guides.

MAINTENACE

Summary of Contents for EBW4023L


















Search results

Summary of Contents for EBW4023L

Reviews:

Related manuals for EBW4023L

Brands by name

Popular brands

Ryobi EBW4023L, Owner'S Operation Manual

Search results

Summary of Contents for EBW4023L

Reviews:

Related manuals for EBW4023L

Brands by name

Popular brands