![background image](http://html1.mh-extra.com/html/ryobi/crh1801/crh1801_owners-operating-manual_1506124006.webp)
3
English
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses with
side shields when operating products. Failure to
do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
■
Drilling in all types of wood products (lumber, plywood,
panelling, composition board, and hard board)
■
Drilling in ceramics, plastics, fiberglass, and laminates
■
Drilling in metals
■
Hammer Drilling in concrete
This product will accept Ryobi One+ 18 V lithium-ion
battery packs and Ryobi One+ 18 V nickel-cadmium
battery packs.
WARNING
Always remove the battery pack from your drill
when you are assembling parts, making adjust-
ments, assembling or removing bits, cleaning,
or when not in use. Removing the battery pack
will prevent accidental starting that could
cause serious personal injury.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximise
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and tool,
the battery pack is depleted. If depleted, the battery pack
will begin charging when placed on a lithium-ion charger.
TO INSTALL A BATTERY PACK
See Figure 2.
Follow these steps to install the battery pack:
■
Place the rotation selector in the centre lock position.
■
Insert the battery pack into the product as shown.
■
Make sure the latches on each side of the battery
pack snap in place and that the battery pack is
secured in the product before beginning operation.
TO REMOVE BATTERY PACK
Follow these steps to remove the battery pack:
■
Depress the latches on each side of the battery pack.
■
Remove the battery pack from the drill.
WARNING
Battery products are always in operating
condition. Therefore, the switch should always be
locked when not in use or carrying at your side.
ADJUSTING THE AUXILIARY HANDLE
See Figure 3.
Follow these steps to adjust the auxiliary handle:
■
Loosen the auxiliary handle by turning the knob
counterclockwise (12).
■
Rotate the auxiliary handle to the desired location.
■
Tighten the auxiliary handle securely by turning the
knob clockwise (11).
ADJUSTING THE DEPTH GAUGE ROD
See Figure 4.
Follow these steps to adjust the depth gauge rod:
■
Lock the trigger switch by placing the rotation selector
in the center position.
■
Loosen the auxiliary handle by turning the knob
counterclockwise (12).
■
Adjust the depth gauge rod so that the drill bit extends
beyond the end of the rod to the required drilling
depth.
■
Tighten the auxiliary handle by turning the knob
clockwise (11).
TRIGGER SWITCH
See Figure 5.
To turn the drill ON, depress the trigger switch. To turn it
OFF, release the trigger switch.
CRH1801_SAA-v5.indd 3
CRH1801_SAA-v5.indd 3
8/31/09 3:27:46 PM
8/31/09 3:27:46 PM
Summary of Contents for CRH1801
Page 1: ...CRH1801 18V SDS ROTARY HAMMER OWNER S OPERATING MANUAL...
Page 9: ......