Page 12
CHISEL SHARPENING
CHISELS AND SCREWDRIVER BLADES
See Figure 10.
When sharpening chisels and screwdrivers, work rest should
support the chisel at the correct angle against the wheel.
OPERATION
Fig. 10
COOLANT TRA
Y
8” Bench Grinder
RYOBI
TECH
NOLOG
IES, IN
C.
Anderson, SC 29625
1-800-525-2579
SER. No.
BGH615 120V AC 60Hz 2.1A 3600 RPM/TR/MN 1/2” Arbor
Por r
azones de seguridad, leer
atentamente el
Manu
al del Usua
rio antes de poner el
uso la máquina. Usar protección de segurida
d p
ara los ojos y discos de amol
ar apto
s
para la velocidad de la máquina.
MADE IN CHINA
FABRIQUE AUX CHIN
A
FABRICADO EN
CHINA
For
Safe Operation, Read
and
Understand O
perator's Manual Before Us
ing Tool.
Wear Eye Protectio
n. Alwa
ys use
Guard
s and use grindi
ng wheels
suitable for speed
of grinder.
Avant utilisation, il faut lire et
comprendre le manu
el d’utilisation po
ur utiliser l’outi
l d’une
manière sûre. Il faut porter d
es
lunettes de s
écurité. Il
faut
tou
jours u
tiliser l
es carters
de protect
ion et uti
liser des meules appropriées pou
r le régime de la meul
euse
.
ADVERTENCIA
WA
RN
IN
G
AVER
TISSE
MEN
T
E
48467 43F1
WHEEL REPLACEMENT
See Figure 11.
If you must replace a grinding wheel, be sure to obtain one
with a safe rated speed greater than the “no load speed”
RPM marked on the data plate of the grinder and which is
marked to comply with ANSI B7.1.
To replace the grinding wheel, remove the wheel cover by
loosening the screws. Loosen the wheel nut in a clockwise
direction for the left side and a counterclockwise direction
for the right side. Remove the outer flange and grinding
wheel. To install a new grinding wheel, reverse the above
procedure. Be sure the grinding wheel and outer flange are
properly seated on the spindle shaft.
WARNING:
Always disconnect the bench grinder from the power
source before performing any assembly or adjustment.
Failure to do so could result in accidental starting resulting
in possible serious personal injury.
Fig. 11
8” Bench Grinder
RYOBI TECHNOLOGIES, INC.
Anderson, SC 29625
1-800-525-2579
SER. No.
BGH615 120V AC 60Hz 2.1A 3600 RPM/TR/MN 1/2” Arbor
Por razones de seguridad, leer atentamente el Manual del Usuario antes de poner el
uso la máquina. Usar protección de seguridad para los ojos y discos de amolar aptos
para la velocidad de la máquina.
MADE IN CHINA
FABRIQUE AUX CHINA
FABRICADO EN CHINA
For Safe Operation, Read and Understand Operator's Manual Before Using Tool.
Wear Eye Protection. Always use Guards and use grinding wheels suitable for speed of grinder.
Avant utilisation, il faut lire et comprendre le manuel d’utilisation pour utiliser l’outil d’une
manière sûre. Il faut porter des lunettes de sécurité. Il faut toujours utiliser les carters
de protection et utiliser des meules appropriées pour le régime de la meuleuse.
ADV
ERT
ENC
IA
WA
RN
IN
G
AVER
TIS
SEM
ENT
E
4846
7
43F1
COOLANT TRA
Y
0FF
0N
SCREW(S)
GRINDING
WHEEL
OUTER
FLANGE
INNER
FLANGE
STAR
WASHER(S)
HEX NUT(S)
WHEEL
GUARD COVER
WHEEL
NUT
SPINDLE
SHAFT
