Ryobi BCL3620S, Original Instructions Manual

Page: 6 / 12

4
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice.
Regulatory Compliance Mark (RCM).
Product meets applicable regulatory
requirements.
The following signal words and meanings are intended to
explain the levels of risk associated with this product.
danGer
Indicates an imminently hazardous situation, which, if
not avoided, will result in death or serious injury.
WarnInG
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CautIon
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CautIon
(Without Safety Alert Symbol) Indicates a situation that
may result in property damage.
enVIronmentaL proteCtIon
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be stored for
environmentally friendly recycling.
deSCrIptIon
1. BCL3620S charger
2. Indicator LED
3. Battery port
4. Key hole hanger
5. Depress latch to remove battery pack
6. Power cord
SpeCIFICatIonS
Battery BPL3625D BPL3626
BPL3640
BPL3640D
BPL3650D
Voltage 36V DC
Charger input
220V-240V,
50/60 Hz AC only
Battery
capacity
2.5 Ah 2.6 Ah 4.0 Ah 5.0 Ah
no. of cell for
battery
10 20 20 20
maximum
charging time
(BCL3620S)
100
minutes
100
minutes
145
minutes
200
minutes
Quick
recharge
60%
1 hour 1 hour 1.5 hour 2.0 hours
operatIon
WarnInG
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WarnInG
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
WarnInG
Never operate the charger where there is a possibility
of inflammable or explosive gases or vapour. Keep well
away from petroleum, paint and cleaning supplies and
gas fired heating systems.
WarnInG
Charge in a well ventilated area. Do not block charger
vents. Keep them clear to allow proper ventilation.
CharGInG the Battery paCk
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
them until the green LED on the front of the charger comes
on.
CharGInG a hot Battery paCk
When using a tool continuously, the batteries in the battery
pack will become hot. You should let a hot battery pack
cool down for approximately 30 minutes before attempting
to recharge.
note: This situation only occurs when continuous use
of a tool causes the batteries to become hot. It does not
occur under normal circumstances. Refer to CHARGING
A COOL BATTERY PACK for normal recharging of
batteries. If the charger does not charge the battery pack
under normal circumstances, return both the battery pack
and charger to your nearest authorised service centre for
electrical check.
CharGInG a CooL Battery paCk
Only charge the Ryobi battery pack BPL3625D/BPL3626/
BPL3640/BPL3640D/BPL3650D with this charger. Make
sure the power supply is normal household voltage, 220-
240 V, 50/60 Hz, AC only. Make sure the battery pack latch
snaps into place and the battery pack is secured in the
charger before beginning operation.
1. Connect the charger to the power supply.
2. Place the battery pack in the charger aligning raised
rib on the battery pack with the groove in the charger.
3. Slide in the battery pack to be sure contacts on the
battery pack engage properly with contacts in the
charger.