![background image](http://html.mh-extra.com/html/ryobi/band-saw/band-saw_operators-manual_1506349005.webp)
Page 5
AVOID
AWKWARD OPERATIONS AND HAND POSI-
TIONS
where a sudden slip could cause your hand to
move into the blade.
ALWAYS
make sure you have good
balance.
ALLOW THE MOTOR TO COME UP TO FULL SPEED
before starting a cut to avoid binding or stalling.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF.
Have defective switches replaced by an
authorized service center.
REPLACEMENT PARTS.
All repairs, whether electrical
or mechanical, should be made by a qualified service
technician at an authorized service center.
WHEN SERVICING
use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause
product damage.
KEEP HANDS AWAY FROM CUTTING AREA.
Do not
hand hold pieces so small that your fingers go under
the blade guard. Do not reach underneath work or in
blade cutting path with your hands and fingers for any
reason.
NEVER CUT MORE THAN ONE PIECE AT A TIME
or
stack more than one workpiece on the saw table at a
time.
FIRMLY CLAMP OR BOLT
your saw to a stable, level
workbench or table. The most comfortable table height
is approximately waist height.
DO NOT FEED THE MATERIAL TOO QUICKLY.
Do not
force the workpiece against the blade.
USE ONLY CORRECT BLADES.
Use the right blade
size, style and cutting speed for the material and the type
of cut. Blade teeth should point down toward the table.
BEFORE MAKING A CUT,
BE SURE ALL ADJUST-
MENTS ARE SECURE.
ALWAYS SUPPORT LARGE WORKPIECES
while cut-
ting to minimize risk of blade pinching and kickback. Saw
may slip, walk or slide while cutting large or heavy boards.
DO NOT REMOVE JAMMED CUTOFF PIECES
until
blade has stopped.
NEVER START THE TOOL
when the blade is in contact
with the workpiece.
NEVER TOUCH BLADE
or other moving parts during
use.
BEFORE CHANGING THE SETUP, REMOVING
COVERS, GUARDS OR BLADES,
unplug the saw
and remove the switch key.
HOLD THE WORKPIECE
firmly against the saw table.
TO AVOID ACCIDENTAL BLADE CONTACT,
minimize
blade breakage, and provide maximum blade support,
always adjust the blade guide assembly to just clear the
workpiece.
KEEP BLADES CLEAN, SHARP, AND WITH SUFFI-
CIENT SET.
Sharp blades minimize stalling and kick-
backs.
ALWAYS TURN OFF SAW
before disconnecting it to
avoid accidental starting when reconnecting to a power
source.
DO NOT OPERATE THIS TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL OR ANY
MEDICATION.
STAY ALERT AND EXERCISE CONTROL.
Watch what
you are doing and use common sense.
Do not
operate
tool when you are tired.
Do not rush.
MAKE SURE WORK AREA HAS AMPLE LIGHTING
to
see the work and that no obstructions will interfere with
safe operation
BEFORE
performing any work using your
saw.
The blade guides have been preset at the factory. These
settings are functional for some applications. We recom-
mend that you check and adjust blade guide settings be-
fore first use of your saw. Refer to
“Adjusting thrust bear-
ings, blade guide support, and blade guides”
proce-
dures explained in the
adjustments
section of this
operator’s manual.
SAVE THESE INSTRUCTIONS.
Refer to them frequently
and use them to instruct other users. If you loan someone
this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals, work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
RULES FOR SAFE OPERATION
SAVE THESE INSTRUCTIONS
Summary of Contents for BAND SAW
Page 23: ...Page 23 NOTES NOTES ...