F
E
D
C
C
B
A
Fig. 1
Fig. 2
B
C
A
D
8 IN. ICE AUGER BIT
FORET DE TARIÈRE À GLACE
DE 203,2 mm (8 po)
BROCA DE BARRENA DE HIELO
DE 203,2 mm (8 pulg.)
AC8ICE
For use with Ryobi
™
P2903 and RY40701 Hole Augers.
WARNING:
This insert sheet is not a substitute for reading the operator’s
manual. To reduce the risk of injury or death, user must read and
understand operator’s manual before using this product.
WARNING:
To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the product when
assembling parts.
WARNING:
Always install the powerhead cover when using the auger in
snow, ice, or wet conditions. Do not allow snow, ice, or rain on
the auger housing or battery pack. Wipe the auger clean with
a dry cloth occasionally. If the cover begins to leak, replace the
cover before using the auger.
n
The ice blade is extremely sharp. Use extreme caution when
drilling a hole or replacing the blade. Install the blade guard after
each use. Always store with blade guard attached.
n
Wear non-slip, heavy-duty protective gloves. Wear non-skid,
protective footwear that will protect your feet and improve your
footing on slippery surfaces.
n
Dress properly. Do not wear loose clothing or jewelry. Keep your
body, hair, drawstrings, scarves, hats, gloves, and loose clothing
away from moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
n
Do not operate any power tool under the influence of alcohol or
drugs.
n
This product translates considerable rotational forces to the
operator. Make sure your feet are firmly planted. Hold both
handles firmly while operating the auger.
n
Do not leave the auger unattended outdoors. Store indoors while
not in use.
n
When drilling ice, do not push down on the auger. If the auger
begins to drill slowly the bit may need to be sharpened or re-
placed.
n
KEEP THE POWERHEAD AND BATTERY DRY AT ALL TIMES.
After the ice bit breaks through the surface, water may overflow
through the hole. To minimize water splash, slow the speed
before the drill breaks through the ice surface, then raise the
tool slowly.
n
Do not expose the auger powerhead or battery to water.
n
Always keep the blade guard on the auger except when in use.
Use caution when removing or installing the blade guard. The
cutting blades are very sharp.
n
Never use a hose, water, or any liquids to clean or rinse off the
auger powerhead. Corrosive liquids, water, and chemicals can
enter the auger powerhead and/or battery pack and damage
the electronic components, which can result in a short circuit,
increased risk of fire, and serious personal injury.
SYMBOLS
Some of the following symbols may be used on this product.
Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the product better
and safer.
SYMBOL
NAME
EXPLANATION
Slippery
Surface
Exercise caution to avoid slipping
or falling.
Wet
Conditions
Alert
R i s k o f f i re a n d b u r n s . D o
not expose battery, battery
c o m p a r t m e n t , o r e l e c t ro n i c
components to rain, water, or
liquids. Close cover during use. Do
not operate on wet ground.
998000628
5-5-21 (REV:01)
TECHTRONIC INDUSTRIES POWER EQUIPMENT
P.O. Box 1288, Anderson, SC 29622 USA
n
1-800-525-2579
n
www.ryobitools.com
Model/item number on product may have additional letters at the end. These letters
designate manufacturing information and should be provided when calling for service.
USING THE POWERHEAD COVER
See Figure 1.
When using in wet conditions, always install the powerhead cover.
Make sure it covers the entire motor/battery housing.
ASSEMBLING THE HOLE AUGER
See Figure 2.
n
Stand the auger bit (B) upright with tip pointing down.
n
Remove the screw (A) from the auger bit (B).
n
Install the drive shaft (D) into the auger bit (B).
n
Align the holes on the auger bit (B) and drive shaft (D).
n
Insert the screw (A) and tighten with included allen key (C).
Please consult your operator’s manual for further information or
contact Ryobi Customer Service at 1-800-525-2579.
ATTACHING THE BLADE COVER
See Figure 3.
n
Align the blades (A) with the recessed pockets inside the blade
cover (B).
n
Insert the notches (C) on the cover (D) onto the blade guard.
n
Rotate cover (D) slightly to the left to tighten in place.
n
Insert one end of the rubber lanyard (E) into the channels (F) on
the blade cover.
n
Secure rubber lanyard (E) across the top of the blade guard.
n
Insert the other end of the rubber lanyard (E) into the channels
(F) on the opposite side of the blade cover (D) to secure.
Fig. 3
A
