Ryobi 770rEB Operator'S Manual Download Page 3

CALIFORNIA EMISSION REGULATIONS

3

SPARK ARRESTOR

WARNING!

RULES FOR SAFE OPERATION

NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington.

All U.S. Forest

Land and the states of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that
certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark
arrestor, maintained in effective working order, or the engine be constructed, equipped and maintained for the prevention
of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these
requirements could subject you to liability or a fine. 

This unit is not factory equipped with a spark arrestor.

If these

items are required in your area, ask your LOCAL SERVICE dealer to install the 

Optional Accessory Part #180030 Spark

Arrestor Kit.

This unit meets the 1995 to 1998 California emissions regulations for small off-road engines. These units are identified by
the label on the engine of your product. A typical identification label is shown.

To ensure that your unit continues to meet these regulations, refer to the following information and instructions in this
operator’s manual.

Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can
result in serious injury to the operator and/or bystanders.

WARNING

California Proposition 65 Warning:

THE ENGINE EXHAUST FROM THIS PRODUCT

CONTAINS CHEMICALS KNOWN TO THE STATE

OF CALIFORNIA TO CAUSE CANCER, BIRTH

DEFECTS OR OTHER REPRODUCTIVE HARM.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-265-6778 in CANADA

The purpose of safety symbols is to attract your 
attention to possible dangers. The safety symbols, 
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by 
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper 
accident prevention measures.

SYMBOL

MEANING

SAFETY ALERT SYMBOL:

Indicates 

danger, warning, or caution. Attention is
required in order to avoid serious personal
injury. May be used in conjunction with 
other symbols or pictographs. 

NOTE:

Advises you of information or instructions vital to
the operation or maintenance of the equipment.

DANGER:

Failure to obey a safety warning

will result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock, and
personal injury.

WARNING:

Failure to obey a safety warning

can result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock, and
personal injury. 

CAUTION:

Failure to obey a safety warning

may result in property damage or personal
injury to yourself or to others. Always follow
the safety precautions to reduce the risk of
fire, electric shock, and personal injury.

Summary of Contents for 770rEB





























Reviews: