Ryobi 766r Operator'S Manual Download Page 6

6

RULES FOR SAFE OPERATION

OTHER SAFETY WARNINGS

Never store the unit, with fuel in the tank,
inside a building where fumes may reach an
open flame or spark.

Allow the engine to cool before storing or
transporting. Be sure to secure the unit while
transporting.

Store the unit in a locked up and dry or high
and dry place to prevent unauthorized use or
damage, out of the reach of children.

Never douse or squirt the unit with water or
any other liquid. Keep handles dry, clean and
free from debris. Clean after each use, see

Cleaning and Storage

instructions.

Keep these instructions. Refer to them often
and use them to instruct other users. If you
loan someone this unit, also loan them these
instructions.

SAVE THESE INSTRUCTIONS

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear
on this product. Read the operator's manual for complete safety, assembly, operating and
maintenance and repair information.

WARNING - READ OPERATOR'S MANUAL 

Read the Operator’s Manual(s) and follow all warnings and safety 
instructions. Failure to do so can result in serious injury to the 
operator and/or bystanders.

MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or caution. May be used in
conjunction with other symbols or pictographs.

• PRIMER BULB

Push primer bulb, fully and slowly, 5 to 7 times.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all bystanders, especially children and pets,

at least 50 feet (15 m.) from the trimming area. 

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• FOR SERVICE INFORMATION, CALL:

USA: 1-800-345-8746
CANADA: 1-800-265-6778

• WEAR EYE AND HEARING PROTECTION

WARNING:

Thrown objects and loud noise can cause severe eye

injury and hearing loss. Wear eye protection meeting ANSI 
Z87.1-1989 standards and ear protection when operating this unit.

SYMBOL

Summary of Contents for 766r



























Reviews: