background image

5

authorised service centre for a thorough cleaning and 

lubrication at least once a year.

 

If the power supply cord is damaged, it must be 

replaced only by the manufacturer or by an authorised 

service centre to avoid risk. Contact authorised service 

centre.

 WARNING

To ensure safety and reliability, all repairs should be 
performed by an authorised service center or other 
qualified service organisation.

ENVIRONMENTAL PROTECTION 

Recycle raw materials instead of disposing 
of as waste. The machine, accessories and 
packaging should be sorted for environment-
friendly recycling.

SYMBOLS ON THE PRODUCT

Safety Alert

V

Volts

Hz

Hertz
Alternating current

W

Watts

n

Rated speed

min

־

¹

Revolutions or reciprocations per minute

Class II, double insulated

Please read the instructions carefully before 
starting the product.

Wear ear protection

Wear eye protection

Wear dust mask.

Do not use chipped, cracked or defective 
grinding wheel

Not for wet grinding. Using water or other 
liquid coolants may result in electrocution or 
shock.

Wear safety hand gloves

 

Regulatory Compliance Mark (RCM). Product 
meets applicable regulatory requirements.

Waste electrical products should not be 
disposed of with household waste. Please 
recycle where facilities exist. Check with your 
local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

Note

Connect to the power supply.

Disconnect from the power supply. 

Parts or accessories sold separately

Lock

Unlock

Stop the product.

Without force

With force

The following signal words and meanings are intended to 

explain the levels of risk associated with this product:

 DANGER

Indicates an imminently hazardous situation, which, if not 

avoided, will result in death or serious injury.

 WARNING

Indicates a potentially hazardous situation, which, if not 

avoided, could result in death or serious injury.

 CAUTION

Indicates a potentially hazardous situation, which, if not 

avoided, may result in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates a situation that 

may result in property damage.

Summary of Contents for 0093236

















Reviews: