background image

Helpline: 0844 856 0793

Email: [email protected]

Website: www.coreservice.co.uk

11

19

Fuel: Unleaded gasoline 90# or above

Step 3 Filling with engine oil

•  Unscrew the motor oil filling bolt (20) and remove it.
•  Carefully pour in motor oil (approx.600 ml). Avoid spilling!
•  Tighten the motor oil filling bolt again by hand.

 

20

Engine oil: SAE 10W-30 grade

Note The appliance is supplied without engine oil. Fill engine oil before commissioning without fail. 

Operating the petrol tiller

Step 1 Check before use

Danger of injury!

Do not operate the device unless you did not find any faults. If a part has

become defective, make sure to replace it before you use the device again.

Check the safe condition of the device:

•  Check the device for leaks.
•  Check the device for visual defects.
•  Check that all parts of the device have been securely fitted.
•  Check that all safety devices are in proper condition.

Step 2 Starting the engine

Risk of device damage!

The lifetime and operating safety of the motor is highly dependant on the running-in 

time. Always allow a cold motor to idle for a few minutes to warm up, and do not use it 

at full power straight away. 

For the first 20 hours of operation (running-in period), do not push the motor to the 

Summary of Contents for HST-1003
























Reviews: