RXTEC RX-PSE808G Quick Installation Manual Download Page 1

8-Port Ethernet Gigabit PoE Switch               Rev 1.0 12/01/2013 Page 1 / 7

IMPORTANT

This users guide contains information on the limitations regarding product use and function and 
information on the limitations as to liability of the manufacturer. Read the entire guide carefully 

• Introduction …………………………………………………..

• Power Over Ethernet (PoE) & Features  ……..…………..

• Unpacking and Installation ……… .………………………..

• System Requirement…….  .………………………………..

• Front Panel /LED….………………………………………….

• Hardware Installation… …………. …………….……….…..

• Technical Specification……………………………………....

• Troubleshooting ………...……………..……..……………... 

Page 2

FCC Warning:

This device has been tested and found to comply with the regulations for Class B digital equipment. Pursuant  to  Part 
15  of FCC Rules.  These  limits  are  designed  to  provide  reasonable  protection against harmful  interference  when  
the  equipment  is  operated in a  commercial  environment. This equipment generates, uses, and can radiate radio 
frequency  energy  and,  if not installed  and  used in accordance with users guide, may cause harmful interference to 
radio  communications. Operation  of this devices in  a residential area is likely to cause  harmful interference, in  which 
case  the  user  will  be  required to correct the interference at his/her own expense.     

CE Mark Warning:

This  is  a  Class  B  product. In a domestic environment, this product may cause radio interference, in which case the user 

may be required to take adequate measures. 

UL Warning:

1> Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the operating ambient  

temperature of the rack environment may be greater then room ambient. Therefore, Consideration should be given to   
installing the equipment in an environment compatible with manufacturer’s maximum rated ambient temperature

2> Reduced Air flow-installation of equipment in a rack  should be such that the amount of air flow required for safe  

operation of the equipment is not compromised.

3> Mechanical Loading- mounting of the equipment in the rack should be such as that a hazardous 

Conditions is not achieved due to uneven mechanical loading.    

Page 2

Page 3

Page 3

Page 4

Page 6

Page 7

Page 5

Table of Contents

Quick Installation Guide

8-Ports Gigabit 10/100/1000M PoE Switch (af Version 15.4W)

Summary of Contents for RX-PSE808G








Reviews: