background image

QUICK USE MANUAL                                                                                                                                                             68090258 

ORIGINALE 

RUTHMANN ITALIA s.r.l.  Via Santa Maria del Piano di Sotto, 91/B - 47854 Montescudo – Monte Colombo (RN) – ITALIA   

pagina 1 

 

 

                            

AERIAL WORK PLATFORM 

Model: 

- SA18  

- SA18HB  

 

 

                       ! 

WARNING 

This  QUICK  USE  MANUAL has  been  written with  the  purpose  of  making  the  first 
approach  simpler  to  the  RUTHMANN  Bluelift  products.  In  this  manual 
RUTHMANN  ITALIA  S.r.l.  are  exemplified  with  images  and  short  message  the 
different phases of use of the aerial work platform from the engine starting to the 
stabilization and lifting.  
It  is  important  remember  that  this  manual  is  not  substitutive  of  the  “USE  AND 
MAINTENANCE MANUAL” issued with the aerial work platform. An improper use 
of  the  machine  can  cause  serious  injuries  or  death.  The  operators  and 
maintenance staff must read the Use and Maintenance manual before using the 
machine and before making any maintenance operation. 
Keep  this  manual  near  the  machine  so  that  it  can  be  consulted  at  any  time  or 
periodically by people who need to be familiar with it. 

 

Summary of Contents for SA18

















Reviews: