Russound MCA-88 Installation Manual Download Page 20

20

Russound MCA-88 Installation Manual

TECHNICAL SPECIFICATIONS

                                       MCA-88 Multizone Controller

 

Dimensions:

  17"W x 3.5"H x 17.2"D (43.2 x 9 x 44 cm)

 

Weight: 

 28.8 lbs. (13.1 kg)

 

Power Supply: 

 100-120 VAC, 60Hz

 

  220-240 VAC, 50Hz

 

Fuse Rating: 

 100-120V/T5.0A 250V US and Canada

 

  220-240V/T3.15A 250V International

 

Frequency Response: 

 20Hz-20kHz +/- 1 dB at 1W output into 8 ohms

 

Minimum Impedance:

  8 ohms

 

Watts per channel:

 40W* 

 

  *1kHz into 8 ohms with <5% THD+N, 

 

  2 channels at full power, 10 channels at 1/8th

 

 

Total Harmonic Distortion:

  <0.05%, 1W output into 8 ohms 20Hz-20kHz

 

Signal to Noise Ratio: 

 93 dB unweighted, 96 dB A-weighted

 

Audio Source Inputs: 

 8 stereo RCA line level, 3 coax,1 optical 

 

  (maximum of 8 total inputs)

  

Audio Zone Outputs: 

 6 Speaker Level 40W/ch

 

  (8 line level, fixed or variable selectable)

 

Common Trigger: 

 Out, 12VDC, @100mA

 

Home Theater Trigger: 

 In/Out, 12VDC (pass-through)

 

Page Trigger: 

In, 12VDC

 

Speaker connection: 

  6 detachable 4 pole connectors

 

Keypad ports:

  6 RJ-45 T568A standard 

 

IR Outputs: 

Up to 6 routed, with two shared outputs  

 

  and 1 common

 

Communication ports:

  USB (firmware update only)

 

  1 Serial RS-232, 19.2 kHz baud rate

 

  1 Ethernet RJ-45, 10/100 Base T 

 

  2 RJ-45 RNET link ports 

LIMITED WARRANTY

Limited Warranty

The Russound MCA-88 Controller Amplifier is guaranteed against all defects 

in materials and workmanship for two (2) years from the date of purchase. 

During this period, Russound will replace any defective parts and correct any 

defect in workmanship without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according 

to its written instructions. If service is necessary, it must be performed by 

Russound. The unit must be returned to Russound at the owner’s expense and 

with prior written permission. Accidental damage and shipping damage are 

not considered defects, nor is damage resulting from abuse or from servicing 

by an agency or person not specifically authorized in writing by Russound.

This warranty does not cover:

•  Damage caused by abuse, accident, misuse, negligence, or improper 

installation or operation

•  Power surges and lightning strikes
•  Normal wear and maintenance
•  Products that have been altered or modified
•  Any product whose identifying number, decal, serial number, etc. has been 

altered, defaced or removed.

Russound sells products only through authorized Dealers and Distributors 

to ensure that customers obtain proper support and service. Any Russound 

product purchased from an unauthorized dealer or other source, including 

retailers, mail order sellers and online sellers will not be honored or serviced 

under existing Russound warranty policy. Any sale of products by an 

unauthorized source or other manner not authorized by Russound shall void 

the warranty on the applicable product.

Damage to or destruction of components due to application of excessive 

power voids the warranty on those parts. In these cases, repairs will be made 

on the basis of the retail value of the parts and labor. To return for repairs, 

the unit must be shipped to Russound at the owner’s expense, along with a 

note explaining the nature of service required. Be sure to pack the unit in a 

corrugated container with at least three (3) inches of resilient material to 

protect the unit from damage in transit.

Before returning a unit for repair, call Russound Tech Support at 

 

(866) 888-7466 for a Return Authorization number. Write this number on the 

shipping label and ship to:

Russound

: ATTN: Service, 1 Forbes Road, Newmarket, NH 03857

Due to continual efforts to improve product quality as new technology and 

techniques become available, Russound/FMP, Inc. reserves the right to revise 

system specifications without notice.

Summary of Contents for MCA-88

























Reviews: