Russell Hobbs RHHD2 Instructions And Warranty Download Page 4

28. Worn-out appliances should be made unusable immediately by pulling out the mains 

plug,  and cutting through the connection cord and removing the plug.  Then dispose 

of the appliance properly. 

 
 

SPEED & HEAT SWITCHES 

 
SPEED  

 

                  HEAT  

 
I    =    Off                    

  I    =  Cold  

II

   =  Low                     

  II   =  Warm 

III 

 High 

        

 

  III   =  Hot 

 
SWITCH (C) (COOL) 
Speed I + Heat I + Cool = GENTLE AIR 
Speed II + Heat I + Cool = STRONG AIR 
 

OPERATING YOUR HAIRDRYER 

SPEED & HEAT SWITCHES 

Ensure the control setting is in the “0” position when the hairdryer is plugged into the 
mains.  Select the required speed and heat setting (as described in table). 

GENERAL 

Wash and condition your hair as desired, then ‘rough-dry’ your hair.  Add mousse or light 
setting agents evenly through the hair for hair protection and a long lasting style.  If 
desired attach the concentrator nozzle.  Start styling your hair at the back and work 
forwards.  After using the attachment allow it to cool first before removing it from the 
hairdryer. 

CONCENTRATOR /STYLING NOZZLE 

The nozzle concentrates air flow on to a small area of air for fast easy styling.  It is ideal 
for blow drying with a comb or styling brush.  Divide your hair into small sections and 
point the dryer along the hair shafts from the roots to the ends, to give a smooth 
professional finish to the hair. 

COOL SHOT 

Use the cool shot setting for approximately 15 seconds after drying a section of hair, to 
set the style. 

DIFFUSER 

The diffuser is simply attached to the air outlet opening of the of the hair drier-like styling 
nozzle.  It makes it possible for you to dry your hair quickly and gently without whirling up 
your hair by virtue of the large-surface air outlet, and adds vitality to every hairdo.  By 
placing the diffuser directly on the scalp, you dry the hairline.  A dry hairline prevents the 
freshly styled hairdo from collapsing.  Ideal for naturally curly, permed or fine hairstyles.  

 
 
 

 

4

Summary of Contents for RHHD2








Reviews: