background image

4

before using for the first time

Before using the toaster for the first time, you need to cure the elements. This will 
remove their protective coating.

This may smell a bit, but it’s nothing to worry about. Just make sure the room is well 

ventilated.
Check that there’s nothing in the slots, set the browning level to maximum (all 

browning level lights on), and operate the toaster without bread by pressing down the 
rear bread carriage handle.
When it’s done, leave it to cool down fully, then you can use it normally.

preparation

  1  Sit the toaster upright on a stable, level, heat–resistant surface.
  2  Don’t put it on or near anything that could be damaged even by moderate heat. 
  4  Don’t put it near or below curtains or other combustible materials.
  3  Route the cable so it doesn’t overhang, and can’t be caught or tripped over.
  5  Plug it into a wall socket (if necessary, switch the socket on). The left four browning 

level lights will light up.

one slot

6  If you’re using only one slot, use the front slot and front bread carriage handle.

two slots

7  If you’re using both slots, you need only lower the rear bread carriage handle. It’ll 

pull the front handle down with it.

making toast

  6  Use the buttons at either end of the browning level lights to lighten 

%

 or darken 

>

 the toast. The browning level lights will come on/go out to indicate the level 

chosen. The more lights showing, the darker the toast.

  8  Put bread centrally into the toasting slot(s) (maximum thickness 28mm).

9  Press the front (one slot), or rear (two slots) bread carriage handle down fully.

,

  The bread carriage handle(s) won’t lock down unless the toaster is connected to 

the electricity supply.

10  The light by the 

$

 button will come on and the elements will heat up.

11  When it’s done, the toast will pop up, the light by the 

$

 button will go out, and the 

elements will turn off.

eject 

$

12  To stop the toaster before it’s finished, press the 

$

 button. The toast will pop up, 

the elements will turn off, and the light by the 

$

 button will go out.

frozen button

This feature takes the guesswork out of toasting frozen bread.

13  Set the browning level at the setting you use with normal, unfrozen bread.
14  Put the frozen bread into the slots, lower the bread carriage handle(s), to start the 

toaster, then press the 

f

 button.

15  The toasting time will be altered automatically to give the same degree of 

browning  you get with unfrozen bread.

16  The light by the 

f

 button will come on, and the element will heat up.

Summary of Contents for 13361









Reviews: