instructions.
4.The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
5.The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories with
incorrect dimensions cannot be adequately protected or
controlled.
6.The configuration of accessories must match the tool. The
use of accessories that cannot be perfectly fitted on the tool
may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
7.Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool or
accessory has fallen, verify that they are not damaged or
install a new accessory. After inspecting or installing an
accessory, test the operation of the tool at maximum speed
and without load for one minute, keeping at a safety
distance. If the accessories are damaged, they will break
during this test.
8.Wear personal protective equipment. Depending on
application, use face shield,safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing
loss.
9.Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate
area of operation.
10.Hold power tool by insulated surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed metal parts of the
power tool “live” and shock the operator.
11.Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand
or arm may be pulled into the spinning accessory.
12.Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
13.Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
14.Regularly clean the power tool’s air vents. The motor’s
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
15.Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
16.Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
Further Safety Instructions for All Operations
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or anyother accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if a polishing mop is snagged or pinched by the
workpiece, the edge of the mop that is entering into the pinch
point can dig into the surface of the material causing the mop
to climb out or kick out. The mop may either jump toward or
away from the operator, depending on direction of the mop’s
movement at the point of pinching. Polishing mops may also
break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
1) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start up. The operator
can control torque reaction or kickback forces, if proper
precautions are taken.
2) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
3) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool in
direction opposite to the wheel’s movement at the point of
snagging.
4) Use special care when working corners, sharp edges, etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
5) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss of
control.
Additional Specific Safety Instructions for Polishers
• Always use eye protection. All users and bystanders must
wear eye protection that conforms to ANSI Z87.1.
• Clean out your tool often, especially after heavy use. Dust
and grit containing metal particles often accumulate on
interior surfaces and could create an electric shock hazard.
• Do not operate this tool for long periods of time. Vibration
caused by the operating action of this tool may cause
permanent injury to fingers, hands and arms. Use gloves to
provide extra cushion, take frequent rest periods and limit daily
time of use.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving
parts.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge
number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized
cord will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension to
make up the total length, be sure each individual extension
contains at least the minimum wire size. The following table
shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from polishing. Wear
protective clothing and wash exposed areas with soap and
water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
instructions.
4.The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
5.The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories with
incorrect dimensions cannot be adequately protected or
controlled.
6.The configuration of accessories must match the tool. The
use of accessories that cannot be perfectly fitted on the tool
may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
7.Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool or
accessory has fallen, verify that they are not damaged or
install a new accessory. After inspecting or installing an
accessory, test the operation of the tool at maximum speed
and without load for one minute, keeping at a safety
distance. If the accessories are damaged, they will break
during this test.
8.Wear personal protective equipment. Depending on
application, use face shield,safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing
loss.
9.Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate
area of operation.
10.Hold power tool by insulated surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed metal parts of the
power tool “live” and shock the operator.
11.Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand
or arm may be pulled into the spinning accessory.
12.Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
13.Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
14.Regularly clean the power tool’s air vents. The motor’s
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
15.Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
16.Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
Further Safety Instructions for All Operations
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or anyother accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if a polishing mop is snagged or pinched by the
workpiece, the edge of the mop that is entering into the pinch
point can dig into the surface of the material causing the mop
to climb out or kick out. The mop may either jump toward or
away from the operator, depending on direction of the mop’s
movement at the point of pinching. Polishing mops may also
break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
1) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start up. The operator
can control torque reaction or kickback forces, if proper
precautions are taken.
2) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
3) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool in
direction opposite to the wheel’s movement at the point of
snagging.
4) Use special care when working corners, sharp edges, etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
5) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss of
control.
Additional Specific Safety Instructions for Polishers
• Always use eye protection. All users and bystanders must
wear eye protection that conforms to ANSI Z87.1.
• Clean out your tool often, especially after heavy use. Dust
and grit containing metal particles often accumulate on
interior surfaces and could create an electric shock hazard.
• Do not operate this tool for long periods of time. Vibration
caused by the operating action of this tool may cause
permanent injury to fingers, hands and arms. Use gloves to
provide extra cushion, take frequent rest periods and limit daily
time of use.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving
parts.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge
number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized
cord will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension to
make up the total length, be sure each individual extension
contains at least the minimum wire size. The following table
shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from polishing. Wear
protective clothing and wash exposed areas with soap and
water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE
REFERENCE.
The term power tool in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b)Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while opera-
ting power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Indicates a potentially hazardous situation,
which, if not avoided, could result in death or serious
injury and/or property damage.
WARNING Read all safety warnings and instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
CAUTION: Indicates a potentially hazardous situation,
which, if not avoided, may result in minor or moderate
injury and/or property damage.
NOTICE: Indicates a potentially hazardous situation,
which, if not avoided, may result in property damage.
EXPLANATION OF SIGNAL WORD
the off-position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a)
Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b)
Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c)
Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d)
Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e)
Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean. Properly
maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g)
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of
the power tool for operations different from those
intended
could result in a hazardous situation.
5) Service
a)
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
ADDITIONAL SAFETY INSTRUCTIONS
1.This tool is designed to be used as a polisher. Read all the
warnings, instructions, indications provided on drawings
and specifications supplied with this tool. Failure to comply
with all the instructions provided may cause electrical shocks,
fire and/or serious injuries.
2.This tool is not intended to be used for smoothing, metal
brushing and cutting operations. The use of this tool for
unintended applications may cause hazards and injuries to
people.
3.The tool must be used with accessories that have been
specifically designed or recommended by the
manufacturer. The fixing of the accessory to the tool does
not guarantee a safe operation; read the following additional
instructions.
4.The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
5.The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories with
incorrect dimensions cannot be adequately protected or
controlled.
6.The configuration of accessories must match the tool. The
use of accessories that cannot be perfectly fitted on the tool
may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
7.Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool or
accessory has fallen, verify that they are not damaged or
install a new accessory. After inspecting or installing an
accessory, test the operation of the tool at maximum speed
and without load for one minute, keeping at a safety
distance. If the accessories are damaged, they will break
during this test.
8.Wear personal protective equipment. Depending on
application, use face shield,safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause hearing
loss.
9.Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate
area of operation.
10.Hold power tool by insulated surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a “live” wire may make exposed metal parts of the
power tool “live” and shock the operator.
11.Position the cord clear of the spinning accessory. If you
lose control, the cord may be cut or snagged and your hand
or arm may be pulled into the spinning accessory.
12.Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
13.Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
14.Regularly clean the power tool’s air vents. The motor’s
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
15.Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
16.Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
Further Safety Instructions for All Operations
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or anyother accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if a polishing mop is snagged or pinched by the
workpiece, the edge of the mop that is entering into the pinch
point can dig into the surface of the material causing the mop
to climb out or kick out. The mop may either jump toward or
away from the operator, depending on direction of the mop’s
movement at the point of pinching. Polishing mops may also
break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
1) Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start up. The operator
can control torque reaction or kickback forces, if proper
precautions are taken.
2) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
3) Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool in
direction opposite to the wheel’s movement at the point of
snagging.
4) Use special care when working corners, sharp edges, etc.
Avoid bouncing and snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
5) Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss of
control.
Additional Specific Safety Instructions for Polishers
• Always use eye protection. All users and bystanders must
wear eye protection that conforms to ANSI Z87.1.
• Clean out your tool often, especially after heavy use. Dust
and grit containing metal particles often accumulate on
interior surfaces and could create an electric shock hazard.
• Do not operate this tool for long periods of time. Vibration
caused by the operating action of this tool may cause
permanent injury to fingers, hands and arms. Use gloves to
provide extra cushion, take frequent rest periods and limit daily
time of use.
• Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in moving
parts.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge
number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized
cord will cause a drop in line voltage resulting in loss of power
and overheating. When using more than one extension to
make up the total length, be sure each individual extension
contains at least the minimum wire size. The following table
shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from polishing. Wear
protective clothing and wash exposed areas with soap and
water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.