Runco DTV-947 Owner'S Operating Manual Download Page 35

7-2

Service Mode

Projector Set-up

Highlight  ‘Projector  Set-Up’ by  pushing  the  control  disc  up  or  down  and  press

ENTER

to display the projector set-up menu.

Within the projector set-up menu, the following items can be consolidated or set
to the desired setting :

- Identification
- Total run time
- Change password
- Change language
- Change projector address
- Change baudrate
- Power up mode

Identification

Highlight 

‘Identification’

with the control disc and press 

ENTER.

The ‘Identification’ screen gives information concerning :

-  Projector  address. To  change  the  address  of  your  projector,  contact  a  qualified
service technician.

- Software version.

- Configuration.

Possible installations :

* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table

- Baud rate PC : transfer speed for communication with an IBM PC (or com-

patible)  or  MAC.  The  baud  rate  of  the  projector  must  be  the  same  as  the
baud rate of the connected computer. When there is a difference, contact a
qualified service technician to make the appropriate changes.

- Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be
displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed

The status can be changed by pressing the ‘TEXT’ key once on the RCU.

- Serial no. : indicates the fabrication number of the projector. This number

can be useful when calling for technical assistance.

ENTER will start the selected item.
EXIT returns to the Service mode menu.

     SERVICE MODE

 
MEMORY MANAGEMENT
 COMMON SETTINGS
  12C DIAGNOSTICS
  

       Select with
          then  <ENTER> 
        <EXIT>  to return.

or

PROJECTOR SET-UP

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

12C DIAGNOSTICS

  

       Select with
          then  <ENTER> 
        <EXIT>  to return.

or

          PROJECTOR SET-UP

              
             TOTAL RUN TIME
         CHANGE PASSWORD
         CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
         CHANGE BAUDRATE
    POWER UP MODE: operating
  

       Select with
          then  <ENTER> 
        <EXIT>  to return.

or

IDENTIFICATION

RUNCO

DTV - 947

Proj. address : 001
Soft. Version  : 6.00
Config.  :Ceiling

       Front

Baudrate PC : 9600
Text : ON
Serial No. : 103589552

Summary of Contents for DTV-947



























































































Reviews: