Ruijie RSR10-01G Hardware Installation Manual Download Page 25

Installation Manual 

Chapter 5    Troubleshooting 

5

 

 Troubleshooting 

5.1 

 

Troubleshooting Power Faults 

For RSR10-01G series, you can determine whether the power s

status of the indicato

ystem has any fault by the 

PWR indi

r, see the description 

occur, please make the following checks: 

„

 

If the router power switch is in the on position. 

„

 

If the 

„

ower supply meets the requirements. 

cator on the front panel. For the normal 

on the first chapter. If any abnormal situations 

„

 

If the power supply switch of the router is in the on position. 

wer cable is connected correctly. 

po

 

If the p

 

arning 

ything is normal but the SYS/PWR indicator is still off, 

please contact the local distributor or technical support team. 

W

If the check shows ever

5.2 

 

Trou
Faul

bleshooting Configuration 

ts 

After the router is powered on, the terminal will show the startup messages described in 

a

figuration system fails, the terminal may display 

 

config

 do

nal parameters: baud rate of 9600; 8 data 

its

rity check; 1 stop bit; no flow control; VT100 for simulation terminal. 

Ch pter 4 if the system is normal. If the con

no messages or illegible codes. 

If the terminal does not display any messages, please make the following checks: 

„

 

Whether the power system is normal. 

„

 

Whether the Console cable is properly connected. 

If the steps above did not solve your problem, it is likely because of wrong configuration 

cable or wrong terminal parameter setting. Please check terminal parameters. 

If illegible codes occur on the terminal, the possible cause is that terminal parameters

 not match. Please check the termi

ured

; no pa

b

Note 

When the console port parameters of your router are modified, this may also 

lead to no display on the terminal. 

 

 

 

5-1

 

 

Summary of Contents for RSR10-01G




























Reviews: