Copyright © 2015 Ruckus Wireless, Inc.
Page 1 of 4
Published 24 July 2015, Part Number 800-70972-001 Rev A
ZoneFlex R310 Access Point
Quick Setup Guide
This
Quick Setup Guide
provides step-by-step instructions on how to set up
your Ruckus Wireless ZoneFlex R310 access point. After completing the
steps in this guide, you will be able to place the access point at your site
and provide network access to wireless clients. The rest of this document
refers to the ZoneFlex R310 access point as an AP.
B
EFORE
Y
OU
B
EGIN
Before deploying your Ruckus Wireless device, please check the Ruckus
Wireless Web site for the latest software and release documentation.
•
Release Notes and User Documents are available at
http://support.ruckuswireless.com/documents
•
Software Upgrades are available at
http://support.ruckuswireless.com/software
•
Open Source information is available at
http://support.ruckuswireless.com/open_source
T
HIS
G
UIDE
IN
O
THER
L
ANGUAGES
•
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
•
Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com
•
https://support.ruckuswireless.com
で ご覧 く だ さ い
•
이
가이드의
한국어
버전은
웹
사이트
(
https://support.ruckuswireless.com
에서
확인하시기
바랍니
다
•
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com
•
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com
Figure 1. ZoneFlex R310 AP
P
ACKAGE
C
ONTENTS
•
One ZoneFlex R310 access point
•
Two mounting screws and plastic wall anchors
•
One T8 5mm M2.5 Torx locking security screw
•
One unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
Declaration of conformity, if required
•
Ruckus Wireless AP Getting Started Guide
•
This
Quick Setup Guide
C
ONFIGURING
THE
AP
•
Step 1: Collecting the AP MAC Address
•
Step 2: Collecting Setup Requirements, Hardware, and Tools
•
Step 3: Connecting Your Computer to the AP
•
Step 4: Preparing Your Computer for AP Setup
•
Step 5: Logging Into the AP Web Interface
•
Step 6: Customizing the Wireless Settings
•
Step 7: Placing the AP at the Site
•
Step 8: Verifying the Installation
Step 1: Collecting the AP MAC Address
•
Write down the MAC address (12 alphanumeric digits) from the
outside of the AP.
Step 2: Collecting Setup Requirements, Hardware,
and Tools
•
A computer with Ethernet adapter running Windows 7 or equivalent,
with Firefox or equivalent web browser.
•
One Cat 5e (or better) Ethernet cable.
•
T8 Torx screwdriver.
•
An AC-to-12VDC power adapter (sold separately)
--OR--
an 802.3af-compliant Power over Ethernet (PoE) switch or PoE
injector.
Step 3: Connecting Your Computer to the AP
A
After removing the AP from its package, place it next to your
computer.
B
Using an Ethernet cable, connect your computer’s network port to the
POE IN
port on the AP.
C
Connect the AC power adapter (sold separately) to the
12VDC
AP
port, and plug the AC power adapter into a convenient and protected
AC power source.
Alternatively, connect the
POE IN
port to a PoE injector or PoE switch
for both power and network connectivity.
Figure 2. AP rear panel
D
After bootup, verify that the
PWR
LED on the AP is a steady green.
Step 4: Preparing Your Computer for AP Setup
A
On your Windows 7 computer, configure your network adapter from
the
Local Area Connection
settings as follows:
•
Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
Note:
The minimum software revision for the AP is base image 100.x or
later, SmartZone 3.2 or later, or ZoneFlex 10.0 or later.
The rest of this document collectively refers to the SCG SZ, vSZ, ZD,
and other controllers as Ruckus Wireless controllers.
Important!
If the AP is to be managed by a Ruckus Wireless controller, then
follow the controller user documents to connect the AP to your local
network and configure it for initial operation. In that case, you may not
need to complete the following steps.
Note:
The following procedures assume that Windows 7 is the operating
system. Procedures for other operating systems are similar.
