Copyright © 2017 Ruckus Wireless, Inc.
Published July 2017, Part Number 800-71267-001 Rev C
Page 2 of 4
Figure 2. Configuring Unleashed from the Mobile App
Step 1b: Setup Using a Web Browser
1
As soon as the Unleashed AP is powered on and connected to
the local network, it boots up and begins broadcasting a
temporary unencrypted WLAN named “Configure.Me-[xxxxxx]”
from both radios.
2
Using your client’s Wi-Fi connection settings, select and
associate to the “Configure.Me-[xxxxxx]” WLAN.
3
Launch a web browser and enter the following into the
browser’s URL bar:
unleashed.ruckuswireless.com
, and press
Enter
.
4
You will be redirected to the Setup Wizard. Complete the steps
in the Setup Wizard and click
Finish
.
Figure 3. Complete the Setup Wizard to set up your Unleashed network
5
Once the Setup Wizard is finished, a “Configuring system
settings and rebooting” progress screen appears. Wait until the
process is complete.
6
Connect to the WLAN that you configured in the Setup Wizard,
and click
OK
to reconnect. You will be redirected to the
Unleashed login screen.
7
Enter your
Admin Name
and
Password
to login.
Figure 4. The Login page
8
Upon successful login you will be presented with the
Unleashed Dashboard, which displays an overview of your
Ruckus Unleashed network.
Figure 5. The Unleashed Dashboard
9
Click
OK
to save your changes.
Your changes are put into effect immediately. Continue with
.
Step 2: Customize Your Wireless LANs
Once the Unleashed Master AP has been initialized, you can fine-tune the settings of your
first WLAN (that you created during the setup wizard), and create any additional WLANs
needed prior to attaching additional Unleashed member APs. Then, when you deploy
additional member APs in whatever order you prefer, they will automatically retrieve all
WLAN configuration settings (and any other settings you have configured) from the
Unleashed Master AP.
1
From the Dashboard, click anywhere in the WiFi Networks section to expand the
display of your deployed WLANs.
2
On the left side of the screen, select the WLAN box for the WLAN you would like to
configure, and click the Edit button to edit the configuration; or click Create to create
a new WLAN.
3
If you made any changes to the original WLAN, you will be disconnected and will need
to reconnect once the changes have been deployed on the AP radios.
Congratulations! Your Unleashed network is now configured and ready for use. You may
now proceed to
Step 3: Deploy Additional Unleashed Access Points
.
Step 3: Deploy Additional Unleashed Access Points
Deploying additional Unleashed member APs is simply a matter of connecting them to the
same Layer 2 network (subnet) and providing power. They will discover the Unleashed
Master and join automatically. No additional steps are necessary.
P
HYSICAL
I
NSTALLATION
Step 1: Connecting and Sealing the RJ-45 Cables
The Unleashed T710 may use zero, or one or two RJ-45 cables, one for Ethernet when
configured as a Root AP (RAP), and another when the Unleashed T710 is supplying PoE out
to a peripheral device, such as a small cell or micro cell radio. When the Unleashed T710
uses RJ-45 cables, connect and seal the cables using the M25 data cable glands as
shown in Figure 3.
WARNING:
Do not use any PoE injector not tested and approved by Ruckus Wireless to
power the Unleashed T710 Access Point.
WARNING:
Do not plug PoE IN power into the PoE OUT port. See Figure 2.
WARNING
:
If using PoE OUT, it is MANDATORY to use the custom Ruckus supplied
60W PoE injector (part #902-0180-XX00), or to use AC power.
WARNING
: If using a PoE switch to supply power to the Unleashed T710, 30W MUST be
reserved for the Unleashed T710 on the switch. Failure to ensure a 30W supply may result
in unpredictable operation of the access point. Additionally, if using a PoE switch, the
Unleashed T710’s PoE OUT port cannot be used to power additional devices.
Figure 2:
PoE IN and PoE OUT ports
1
Feed the end of the cable through the sealing nut, rubber O-ring, clamping ring
assembly and cable gland base as shown in Figure 3.
Figure 3:
RJ-45 cable and cable gland assembly
2
Use a wide flat-blade screwdriver to remove the required (RESET/PoE OUT or PoE IN)
blanking cap from the Unleashed T710.
3
Connect the cable to the Ethernet port in the Unleashed T710.
4
Tighten the cable gland base into the Unleashed T710 chassis to 7 N.m or 62 in-lbs.
5
Wrap the clamping ring assembly around the rubber O-ring. Make sure that the
clamping ring assembly fully encloses the rubber O-ring.
6
Seat the clamping ring assembly and rubber O-ring in the cable gland base.
7
Hand-tighten the sealing nut.
Cable gland base
Clamping ring assembly
Rubber O-ring
Sealing nut