manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Hardware Installation Manual

Share
Download
Ruckus Wireless ICX 7150-24 Hardware Installation Manual Download Page 111

Regulatory Statements

•

CE statement........................................................................................................................................................ 111

•

China ROHS..........................................................................................................................................................111

•

BSMI statement (Taiwan)....................................................................................................................................... 111

•

Canadian requirements..........................................................................................................................................112

•

China CCC statement........................................................................................................................................... 112

•

Europe and Australia (CISPR 32 Class A Warning).................................................................................................113

•

FCC warning (US only).......................................................................................................................................... 113

•

Germany statement...............................................................................................................................................113

•

KCC statement (Republic of Korea)....................................................................................................................... 113

•

VCCI statement.....................................................................................................................................................113

CE statement

ATTENTION
This is a Class A product. In a domestic environment, this product might cause radio interference, and the user might be required
to take corrective measures.

The standards compliance label on this device contains the CE mark which indicates that this system conforms to the provisions of the
following European Council directives, laws, and standards:

•

Electromagnetic Compatibility (EMC) Directive 2014/30/EU

•

Low Voltage Directive (LVD) 2014/35/EU

•

EN 55032/EN 55024 (European Immunity Requirements)

–

EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)

–

EN61000-3-3

China ROHS

Refer to the latest revision of the China ROHS document (P/N 53

‐

1000428

‐

xx) which ships with the product.

BSMI statement (Taiwan)

Warning:

This is Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to
take adequate measures.

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

111

Summary of Contents for ICX 7150-24




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands