Ruby Tech GS-2108C User Manual Download | Manualshive

Page: 65 / 254

background image

GS-2108C User Manual

Publication date: April, 2008

Revision A4

53

Mode:

Set the speed and duplex of the port. In speed, if the media is 1Gbps
fiber, it is always 1000Mbps and the duplex is full only. If the media is TP,
the Speed/Duplex is comprised of the combination of speed mode,
10/100/1000Mbps, and duplex mode, full duplex and half duplex. The
following table summarized the function the media supports.

Media type

NWay

Speed

Duplex

1000M TP

ON/OFF

10/100/1000M

Full for all, Half for 10/100

1000M Fiber

ON/OFF

1000M

Full

In Auto-negotiation mode, no default value. In Forced mode, default
value depends on your setting.

Flow Control:

There are two modes to choose in flow control, including Enable and
Disable. If flow control is set Enable, both parties can send PAUSE frame
to the transmitting device(s) if the receiving port is too busy to handle.
When it is set Disable, there will be no flow control in the port. It drops
the packet if too much to handle.

Default: Enable.

Wait State:

For more details about this parameter please refer to section 3-2-1.

Default: Disable.

«
...
63
64
65
66
67
...
»

Summary of Contents for GS-2108C































































































































































































































































Reviews:

No comments

Related manuals for GS-2108C

Brand: Dataprobe Pages: 31

Brand: IBM Pages: 13

Flex System EN2092

Brand: IBM Pages: 2

Brand: Dahua Pages: 17

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

CRSMEO-4 Series

Brand: Festo Pages: 16

Brand: Manhattan Pages: 2

Brand: nedis Pages: 24

IIOT-AMS Tilt Counter

Brand: ROSSMA Pages: 13

Brand: Netis Pages: 9

Brand: SALZ Pages: 2

Brand: Imagine Pages: 93

MPD-DS-WML-NFDS Series

Brand: Larson Electronics Pages: 2

Tuffset 200302F

Brand: VXI Pages: 2

Brand: QSFPTEK Pages: 10

QSW-M3212R-8S4T

Brand: QNAP Pages: 29

Brand: Q3 ENERGIE Pages: 28

Brand: QNAP Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands