GB
Junction Box Receiver RCJ06
99318 0711 D/GB
prog.
L
N
12
µ
14
11
Model
RCJ06-5001E-01
1-channel 868.30 MHz
Technical Data
Frequency:
868.30 MHz
Modulation:
FSK
Power supply:
230 V AC / 50 Hz
Current consumption:
approx. 0,8 W
Output:
1 potential-free relay
contact (SPDT)
Max. contact rating:
see Table of Load
Degree of Protection:
IP40
Operating temperature:
-20°C to +60°C
Dimension:
48 x 48 x 25 mm
Table of Loads
Type of Load
max. load
Resisitive Load:
Light bulbs, 230 V
Halogen lamps etc.
10 A / 1,380 VA
Inductive Load:
Halogen lamps with wound
transformers
3 A / 600 VA
(transformator at least 85% loaded)
Non-compensated or series-
compensated fluorescent lamps
with ferromagnetic ballasts
6 A / 1,380 VA
Parallel-compensated
fluorescent lamps with
ferromagnetic ballasts
3 A / 600 VA
Capacity EB:
electronic
ballasts, electronic
transformers etc.
6 A / 920 VA
Safety Advice
Carefully read through these instruc-
tions before connecting and operat-
ing the unit!
Caution! Electrical installation may only be
carried out by a qualified electrician!
Observe the applicable laws, standards and
regulations as well as the manufacturer’s instruc-
tions for the devices to be operated!
Note the maximum load (see Table of Loads)!
Have faulty units checked by the manufacturer!
Do not make any unauthorized alterations or
modifications to the unit!
The relay contact is suitable for a potential-free
power supply in compliance with EN 60664.
Intended Use
This unit may only be used as an Easywave Junc-
tion Box Receiver together with low-powered or
mains-powered devices!
The manufacturer shall not be liable for any damage
caused by improper or non-intended use!
Function
The Junction Box Receiver is designed for switching
low-powered or mains-powered devices in the
operating modes »ON/OFF« or »Dead Man’s
Mode«.
The receiver can be operated by multi-channel
transmitters or single-channel transmitters.
Using the Receiver
Start-Up
1. Mount the receiver in accordance with the on-
site conditions.
Note:
The receiver fits into almost every junc-
tion box.
2. Connect the power supply and the device to be
switched according to the connection diagram.
Caution!
Observe the applicable electrical regu-
lations!
After connecting the receiver is in the
operating mode. The LED is off.
3. Transfer the codes of the transmitters to the
receiver (see section “Memorizing the Trans-
mission Codes“).
Mounting Advice:
avoid mounting at the following
locations, because this will affect the range:
•
in a distribution box or housing made from metal
•
in the immediate vicinity of large metal objects
•
on the ground (or near it).
Programming and Operating Modes
For programming (see “Memorizing the Transmis-
sion codes (Programming)” there are 3 program-
ming modes for the 3 operating modes of the radio
control.
The programming modes are displayed by different
LED flashing patterns.
Prog.
Mode
Operating Mode
LED Flashing
Pattern
1
ON/OFF (2-button
operation)
2
ON/OFF (1-button
operation),
Button operation
> 1.6 seconds: OFF
3
Dead Man’s Mode
(Relay is triggered
as long as the
transmitter button is
pressed)
You can change from the operating mode to the
programming mode 1 and from one programming
mode to the next by briefly (< 1.6 sec.) pressing the
programming button: Operating Mode –> Pro-
gramming Mode 1 –> Programming Mode 2 –>
Programming Mode 3 –> Operating Mode etc.
Memorizing the Transmission Codes
(Programming)
In the “Memorizing the Transmission Codes” mode
you can transfer the codes of your transmitters to
the receiver.
Note:
Generally you only have to transfer the code
of one button per transmitter channel. The code of
the other transmitter buttons will be assigned auto-
matically.
1. Briefly (< 1.6 sec.) press the programming
button.
Programming mode 1 is activated. The LED
flashes. If necessary change the programming
mode (see “Programming and Operating
Modes“).
2. Press and hold a transmitter channel button. As
soon as the code has been memorized, the LED
lights up for 4 sec. and than flashes again. Re-
lease the transmitter button.
3. Repeat step 2 with the other transmitters. The
receiver can memorize up to 32 transmitter
codes.
4. Briefly (< 1.6 sec.) press the programming
button to return to the operating mode.
Note:
In case of longer power failure the program-
ming of the receiver remains.
Deleting Specific Codes
In the delete mode you can delete specific trans-
mission codes memorized by the receiver.
1. Keep the programming button pressed for more
than 1.6 sec. The delete mode is activated. The
LED flashes rapidly.
2. Press the selected transmitter channel button. If
the code has been deleted, the LED lights up for
4 sec. and then flashes again rapidly.
3. Repeat step 2 with another transmitter or briefly
(< 1.6 sec.) press the programming button to re-
turn to the operating mode.
Reset (Deleting Memory Completely)
In the Reset mode you can delete all codes memo-
rized by the receiver.
1. Keep the programming button pressed for more
than 1.6 sec. The delete mode is activated. The
LED flashes rapidly.
2. Press the programming button again and keep it
pressed for more than 1.6 sec. As soon as the
memory has been deleted completely, the LED
lights up for 4 sec. and then flashes again rapid-
ly.
3. Briefly (< 1.6 sec.) press the programming
button to return to the operating mode.
General Information
Disposal
Waste electrical products should not be dis-
posed of with household waste!
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Warranty
Within the statutory warranty period we undertake to
rectify free of charge by repair or replacement any
product defects arising from material or production
faults.
Any unauthorized tampering with, or modifications
to, the product shall render this warranty null and
void.
Conformity
This product complies with the essential
requirements of the R&TTE directive
1999/5/EG.
The Declaration of Conformity can be found on the
internet at: www.eldat.de.
Customer Service
If, despite correct handling, faults or malfunctions
occur or if the product was damaged, please contact
the company at the address below:
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Telefax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
e-Mail: [email protected]
Programming button with LED
Art.-No. G66 031 08
RTS Automation Vertriebsges. Ltd.
Warschauer Str. 7
DE-03042 Cottbus
Phon: +49 355 280 9311
Mail: [email protected]
Internet: www.rts-automation-limited.de
