Touchscreen Control Panel
It’s Under Control
®
VSW-51 FRONT AND REAR PANEL DESCRIPTION
Installation & Operation
SOURCE
MIC
VOLUME
1-HDMI/MHL
5-VGA
4-DP
3-HDMI
2-HDMI
AUTO
ENTER
MENU/2s
1
2
3
4
5
6
7
8
DC 24V
48V
LINE
MIC INPUT
MIC
FIRMWARE
AUDIO OUT
L
R
RES RESET
RS232
INPUTS
OUTPUTS
3-HDMI
2-HDMI
1-HDMI / MHL
4-DP
5-VGA
HDMI
HDBT
CONTROL
IR IN
IR OUT
A
B
C
D
E
F
No.
Name
Function
1
Power LED Indicator
Turns green when power is on, or it turns red when in standby mode.
2
1-HDMI/MHL
1-HDMI/MHL input selector and activity LED / Left Key for On Screen Display control (OSD).
3
2-HDMI
2-HDMI input selector and activity LED / Right Key for OSD control.
4
3-HDMI
3-HDMI input selector and activity LED / Up Key for OSD control.
5
4-DP
Display Port input selector and activity LED / Down Key for OSD control.
6
5-VGA
VGA input selector and activity LED / Enter Key for OSD control.
7
AUTO
Auto-switching selector and activity LED
•
Press this to enter/exit auto-switching mode/OSD menu button.
•
Hold this button down for 3 seconds to enter On Screen Display menu (OSD).
NOTE:
When you set the VGA input port to C-Video or YPbPr in Manual-switching mode, the system will not be
able to enter auto-switching mode.
8
Volume Adjustor
Volume knob for variable audio control - Push knob in to toggle between ‘Mic’ and ‘Source’ control.
A
INPUTS
•
Video input ports: 1 HDMI/MHL, 2 HDMI inputs, 1 Display Port and 1 VGA.
•
Audio input ports: 1 Display Port external audio input and 1 VGA auxiliary audio input.
B
OUTPUTS
•
HDMI output: HDMI video output port.
•
HDBaseT output: Supports PoH. Connect to the VSW-51R or a compatible HDBaseT receiver to transmit A/V,
IR and RS-232 control.
C
MIC INPUT
•
Mic audio port connects to microphone.
•
Dial switch: Switches between 3 different modes; 48V for condenser mics, MIC mode for dynamic mics and
LINE mode for line level audio.
D
CONTROL
•
RES RESET: Press this to reset output resolution to 720p or to activate HDMI and HDBT outputs if they have
been turned off.
•
IR IN: Connect to control system or IR receiver (with carrier wave only) to receive IR signal to control far-
end device which was connected to HDBaseT Receiver via HDBaseT output port.
•
IR OUT: Connect to IR emitter to control local source devices from remote.
•
FIRMWARE: Type-A USB port for updating firmware.
•
RS-232: Serial port, connect a control system for control of the VSW-51.
•
TCP/IP: Ethernet port, connect to LAN for control of the VSW-51 via control system or PC.
E
AUDIO OUTPUT
Stereo balanced L/R audio output.
F
DC 24V
Locking power port, connect to 24VDC power adapter.
CONNECTION DIAGRAM
RX
TX
DC 24V
48V
LINE
MIC INPUT
MIC
FIRMWARE
AUDIO OUT
L
R
RES RESET
RS232
INPUTS
OUTPUTS
3-HDMI
2-HDMI
1-HDMI / MHL
4-DP
5-VGA
HDMI
HDBT
CONTROL
IR IN
IR OUT
IR Emitter
Camera
Laptop
TV Remote
Microphone
Speaker
Control System
Laptop
TV
VSW-51R
VSW-51
DVD Remote
IR Receiver
DVD
TV
IR Emitter
VGA:
HDMI:
Audio:
HDBaseT:
IR Control:
Control:
Pad
IR Receiver
Router
RS-232 CONTROL
To control the VSW-51 using serial communication from a control system, wire the RS-232 output of the control system to the VSW-51
RS-232 connector. Baud rate: 9600, Data bit: 8, Stop bit: 1, Parity bit: none
TCP/IP CONTROL
To control the VSW-51 using TCP/IP protocol from an RTI control system or the web GUI, wire the Ethernet port of VSW-51 TCP/IP
connector to the LAN, set to the same network segment.
•
Default IP: 192.168.0.178
•
Subnet Mast: 255.255.255.0
•
Gateway: 192.168.0.1
•
Serial Port: 4001
NOTE:
IP and gateway settings can be changed as needed, but the Serial Port (4001) can not be changed.
•
Type the IP address h
ttp://192.168.0.178
into the browser address bar to access the web-based GUI interface.
•
Type in the default username:
user
and password:
user
BUTTON CONTROL
Front panel buttons can be used for switching operations and volume adjusting.
•
Press
1-HDMI/MHL
,
2-HDMI
,
3-HDMI
,
4-DP
,
5-VGA
on front panel to select the corresponding input source.
•
Press
AUTO
to enter in auto-switching mode.
Press Volume Knob to choose MIC/Source audio needed to be adjusted, the corresponding LED will turn blue and keep on.
•
Adjusting the Volume Knob in clockwise direction to increase sound volume.
•
Adjusting the Volume Knob in anti-clockwise direction to decrease sound volume.
OSD MENU CONTROL
The switcher provides a powerful OSD operation menu, containing 3 parts: Optional settings, image settings, and system setting etc.
There are two ways to enter OSD menu:
•
Press and hold the button
MENU/2s
on front panel 2 seconds or more.
•
Send command on RS-232 Control Software.
Operation:
•
Press direction buttons on front panel to switch between menu options and menu pages.
•
Press
ENTER
on front panel to confirm the selection.
VSW-51R FRONT PANEL DESCRIPTION
RX
TX
HDCP
LINK
1 2 3
A B C
D
E
F
No.
Name
Function
1
LINK LED Indicator
Turns blue when the VSW-51 switcher and the VSW-51R receiver are connected successfully.
2
HDCP LED Indicator
•
Turns blue when the HDMI signal is transmitted with HDCP.
•
Blinks blue when the HDMI signal is transmitted without HDCP.
•
Turns off when there is no HDMI signal (no picture).
3
Power LED Indicator
Turns red when power on.
INSTALLATION
Please visit the RTI dealer portal (www.rticorp.com/dealer) for additional instructions and specifications.
NOTE: Features and specifications subject to change without notice.
No.
Name
Function
A
RS-232
3-pole captive screw connector for RS-232 pass-through control.
It can be connected with control system (Use a 3-pole captive to 9 pin female D connector) , or
connected with the device which needs to be controlled.
B
IR IN
3.5mm jack for connection to a control system IR output or IR receiver to collect IR signal.
Works with VSW-51 IR OUT.
C
IR OUT
3.5mm jack for connection to an IR emitter for control of external device. Works with VSW-51 IR IN port.
D
HDMI OUT
Type A female HDMI output port to connect HDMI display.
E
HDBT IN
RJ45 HDBaseT input port to connect to the HDBaseT output port of the VSW-51 switcher by CATx cable.
F
DC 24V
Power port to connect the 24V DC power adapter.
VSW-51R REAR PANEL DESCRIPTION
