Touchscreen Control Panel
It’s Under Control
®
FRONT PANEL DESCRIPTION
Installation & Operation
CONTROL
INPUT SEL
1
2
3
LINE
BASS
VOLUME
1
2
3
4
5
No.
Name
Function
1
Power Indicator
Turns red when power on.
2
Audio Input Selection
Press button to select the input audio source. Once selected, the corresponding LED will be lit.
•
1 is for dual mono audio input (2 RCA connectors for L&R)
•
2 is for stereo audio input (3.5mm mini jack)
•
3 is for digital fiber audio input (optical)
3
Audio Control
Press this button to select the Line volume level or the Bass and Treble level. Once selected, use
the Adjustment Knob to adjust level.
4
Adjustment Knob
•
Rotate the knob to adjust audio levels. Volume bars will change accordingly.
•
Press the knob to mute/umute the corresponding audio.
5
Volume Bar
Indicates real-time volume setting, 10 bars in total.
REAR PANEL DESCRIPTION
LOOP
3
1
DC 36V
RS232
Tx
Rx
AUDIO
OPTICAL
L
R
2
TCP/IP
2x50W 8
@
Ω
1x100W 4
@
STEREO
MONO
6
5
7
8
9 10
1
2
3
4
No.
Name
Function
1
Audio Input 1
2 x RCA L&R stereo audio inputs.
2
Audio Input 2
3.5mm mini jack for stereo audio input.
3
Audio Input 3
Optical connector for digital audio input.
4
Audio Loop Output
If a second AMR-350 is required, plug a 3.5mm TRS to 3.5mm TRS cable between the LOOP output
and Input 2 of the second AMR-350.
5
TCP/IP
RJ45 connector for TCP/IP control. For connection to local network for control via a control system
or PC.
6
RS-232
3-pole captive screw connector for serial control, it can be connected with control system (Use a
3-pole captive to 9 pin female D connector) to control AMR-350.
7
Output Mode Selector
2-pole switch for output mode selection.
STEREO –
2x50W@8Ω
.
MONO –
1x100W@4Ω
.
8
Audio Output
To connect with audio output devices, such as speakers (The connection type of speakers depends
on the audio output mode:STEREO or MONO).
9
Power Port
To connect with the power adapter (36V DC).
10
GND
Ground Connection
.
CONNECTION DIAGRAM
LOOP
3
1
DC 33V
RS232
Tx
Rx
AUDIO
OPTICAL
L
R
2
TCP/IP
2x50W 8
@
Ω
1x100W 4
@
STEREO
MONO
LOOP
3
1
DC 33V
RS232
Tx
Rx
AUDIO
OPTICAL
L
R
2
TCP/IP
2x50W 8
@
Ω
1x100W 4
@
STEREO
MONO
Audio Player
Speaker
DVD
Laptop
Laptop
Central Control System
BUTTON CONTROL
Audio Switching
The INPUT SELECT button will switch between:
•
Input 1: RCA analog audio input.
•
Input 2: 3.5 mm TRS input.
•
Input 3: Optical digital audio input.
Volume and EQ Control
•
The CONTROL level selection button will switch between LINE, BASS, and TREBLE levels.
•
When LINE is selected, rotate the knob (+ -) to adjust the volume, or press this knob to mute the selected input audio.
•
When BASS or TREBLE are selected, rotate the knob (+ -) to adjust the bass or treble levels of the analog audio input signal.
CONTROL
INPUT SEL
1
2
3
LINE
BASS
VOLUME
RS-232 CONTROL
To control the AMR-350 using serial communication from a control system, wire the RS-232 output of the control system to the AMR-350
RS-232 3-pole screw connector (pinout: Tx-Gnd-Rx).
•
Baud rate: 9600
•
Data bit: 8
•
Stop bit: 1
•
Parity bit: none
TCP/IP CONTROL
To control the AMR-350 using TCP/IP protocol from a control device, wire the Ethernet port of the control system to the AMR-350 TCP/IP
connector, and then set same network segment for the AMR-350 and control device.
•
Default IP: 192.168.0.178
•
Subnet Mast: 255.255.255.0
•
Gateway: 192.168.0.1
•
Serial Port: 4001
IP and gateway can be changed as need, but the Serial Port can not be changed.
Type the IP address
http://192.168.0.178
into the browser address bar to access the web interface.
INSTALLATION
Visit the RTI dealer portal (www.rticorp.com/dealer) for additional instructions and specifications.
NOTE: Features and specifications subject to change without notice.
