background image

WEIGHT LIMITS

P.13

RTA-9500TV

P.13

• Do not exceed the indicated weight limits.

• Do not expose the surfaces to direct sunlight or to extreme environmental conditions.

• Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and

water, then dry with a clean towel.

• Do not use solvents or abrasive materials to clean the unit.

• If you decide to use a cleaning agent, test first on an area hidden from view such as

underneath the tabletop.

• Do not sit on the unit or lean against it.

• Do not allow small children to climb on the unit to reach the TV set.

• Do not allow small children to reach inside the compartments without your supervision.

• Always be careful and keep your hands and fingers clear of the sliding doors.

• Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by

at least 2 persons when moving in the same or adjacent rooms.

• Before moving the unit, remove your TV set and also remove or secure any other objects

that are heavy or might fall off.

• When lifting the unit, use both hands and bend your knees, not your backs.

• When transporting the unit to places far away, protect and secure the unit to avoid damage

in transit.

• Shall any part of the unit become defective during the warranty period, replacement parts

might be available to you at no charge. Please refer to the last pages on this manual.

• The warranty does not extend to regular wear and tear, nor the manufacturer assumes

liability for damages or consequences due to accidents, incorrect assembly, negligence,

improper use, modifications, or not heeding the above warnings.

CARE, MAINTENANCE AND SAFETY WARNINGS:

A

C

C

C

B

B

C

= 4 KG - 8.81LB

A

 

= 21 KG - 46.29LB

B

 

5

 KG - 

11.02

LB

Summary of Contents for Techni Mobili RTA-9500TV


















Reviews: