manualshive.com logo in svg

RSF Woodburning Fireplaces OPEL3, Owner'S Manual

Share
Download
RSF Woodburning Fireplaces OPEL3 Owner'S Manual Download Page 9

OPEL3 Owner's Manual 

9 

RSF Woodburning Fireplaces 

GOLD PLATING 

If you have gold louvers, you will be happy to know that they will not tarnish.  However, they are not scratch 
resistant. Use only mild soap and warm water to clean the gold when the surface is cool. The use of any 
household cleaner, such as Windex, abrasive cleaners, or any form of acid, may permanently etch or remove 
some of the gold plating. Before the first fire, make sure to clean all fingerprints and other deposits on the gold 
plating. Since the plating cures during the first fire, fingerprints and other deposits will permanently etch the gold 
plating.

  

INSTALLATION 

Check with your local authority having jurisdiction (such as municipal building department, fire department, fire 
prevention bureau, etc.) regarding restrictions and installation requirements, and the need to obtain a permit. 

Remove the fireplace door. Store them in a safe place until the installation and finishing work is finished. Be 
aware that heavy duty cleaning products or acid solutions will permanently damage the plating. 

LOCATION 

Your OPEL3 fireplace may be installed in many different ways (see Figure 5) without any special floor 
reinforcement. We recommend that you take the time to plan your entire installation (fireplace, chimney, and 
options) before beginning the actual installation (refer to Figure 6 and Figure 7).  

 

 

 

Dimensions of the fireplace along with clearances are shown in Figure 1 and Table 1. 

™

 WARNING: IF THIS FIREPLACE IS NOT PROPERLY INSTALLED, A HOUSE FIRE CAN RESULT. FOR 

YOUR SAFETY, FOLLOW THE INSTALLATION INSTRUCTIONS AND CLEARANCES. DO NOT PACK 
REQUIRED AIR SPACES WITH INSULATION OR OTHER MATERIALS. 

1.  Note the location of roof and floor joists. Try to choose a location that does not require cutting them.  

2.  If at all possible, run the chimney up through the inside of the house. If it must be run outside, it should be 

enclosed in an insulated enclosure (see Installation: Chase Enclosure). Remember, a cold chimney causes 
poor draft. 

 

51"

38"

24"

 

82"

38"

58"

18"

The framing dimensions are larger than required for ease of installation. Examples shown here are for a 
Louvered OPEL3. An extra 12" is required on the left of the fireplace of a Clean Face OPEL3 to connect the 
intake air duct. The Heat Dump Option will also require an extra 12" on the selected side. 

Figure 5 Louvered OPEL3 Framing Examples 

Summary of Contents for OPEL3

























Reviews:

No comments

Brands by name

Popular brands

Load more brands