16
15
RSC -1400C/H
16. SPECIFICATIONS
Description
RSC-1400H
RSC-1400C
Power supply
AC 100, 200, 220~240V 50/60Hz 120V 60Hz
Power consumption
1650W, 800W
100W
Max laminating width
1400mm / 55"
Film thickness
25~250 mic / 1~10mil
Max laminating speed
5m/min / 16.4ft/min
Ready time
10min
Not applicable
Heating method
Hot Roller
None
Driving motor
DC geared
Max Temperature contro
l5
0
o
C / 122
o
F
Not applicable
Speed control
9 settings
Transport type
2 Roller
Film core size
Auto grip (2",3")
Cross cutter
Yes
Hot lamination
Yes
N
o
Cold lamination
Yes
Mounting thickness
15mm / 0.6"
Take up system
Chain link to main motor
Reverse
Yes
Remote control
Yes
Foot pedal
Yes
Unit dimensions
1710
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
650
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
1210 (mm)
(w x d x h)
67.5"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
21.5"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
47.5"
Unit weight
164kg / 361lbs
Carton dimensions
1960
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
900
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
850(mm)
(w x d x h)
77"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
35.5"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
33.5"
Gross Weight
270kg / 595lbs
14. MAINTENANCE
15. TROUBLESHOOTING
Cleaning the Body of the laminator
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.
Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Symptom
Cause
Possible Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch(es) is (are) engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Disengage the emergency switch(es).
b. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
a. Did not raise the temperature.
a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
