manualshive.com logo in svg

Rowe 7770, Field Service Manual And Parts Catalog, Page: 65 / 110

Share
Download
Rowe 7770 Field Service Manual And Parts Catalog Download Page 65

5 - 4

 Part No. 900-68702

7800 Deluxe Snack / Candy Vendors  Field Service Manaul & Parts Catalog

UNIVERSAL SHELF
CONVERSION

1.

Converting from a Dual Helix to a
Single Helix selection.
a. Remove the left and right helixes.

b. Remove the right side helix hub

using the Hub Removal Tool
(P/N 593-902).

c. Remove the left side gear hub by

unscrewing the black rivet plate on
the idler box.

d. Remove the idler box from the shelf

weld assembly. Press down on the
top locking tab and push outward.

e. Remove the motor assembly by

pressing down on the top locking
tab and pushing outward.

f. Rotate the motor 90

o

 counter-

clockwise.

g. Reinstall the motor assembly to the

lower opening by snapping it in
place.

h. Install the helix hub by positioning

the hub slot opening to the right and
pushing in until it snaps on.

i. Install the main larger helix spiral to

the helix hub.

j. Reposition the product adjustable

wall as desired.

2.

Converting from a single to a
dual helix.

a. Remove the helix.

b. Remove the helix hub by using the

hub removal tool (P/N 593-902)
supplied in vendor.

c. Remove the product adjustable

wall for extra space.

d. Remove the motor assembly

from the shelf weld assembly by
pressing down on the top locking
tab and pushing motor assembly
outward.

e. Rotate the motor 90

o

 clockwise.

f. Reinstall the motor assembly to the

right most slot opening.

g. Reinstall the helix hub by positioning

the hub slot opening to the right and
pushing until it snaps on.

h. Install the idler box to the left most

slot opening.

i. Install the gear hub using the black

rivet plate. Position the gear hub
with its slot opening to the left side.

j. Install the larger size helix to the

right side hub and install the
smaller size helix to the left side
gear hub.

k. Reposition the Product Adjustment

Wall as desired.

Summary of Contents for 7770















































































































Reviews:

No comments