Rovin MWA632 Operation Instructions Download Page 4

4

5

(Fi

gure 3

VII. Fault Handling

Fault       Inspection 

Solution 

The air 

pump 

cannot be 

started 

normally. 

1. The power source 

is not plugged 

properly. 

2. The fuse in DC 

plug (7) is burnt out. 

3. Overheating or 

overload causes 

motor stop. 

1. Check whether 

the hose is blocked 

or cracked. 

2. The joint between 

the hose and air 

pump or air bag is 

not installed 

properly. 

1. Make sure that the power wire is 

plugged in the 12V DC socket. 

2. Change the fuse. 

3. Cool the motor and restart it. 

4. If the problem cannot be solved, 

please contact with the 

manufacturer or its service agent or 

the similar authorized personnel. 

1. Change the hose or make it 

unblocked, and check whether the 

hose is cracked. 

2. Reinstall the hose. 

3. If the problem cannot be solved, 

please contact with the 

manufacturer or its service agent or 

the similar authorized personnel.

Slow or 

abnormal 

inflation. 

VIII. Maintenance and Storage

After using, or if you want to move, maintain or adjust the product, 

please first pull out the DC plug from the socket. 

when it is idle, it shall be properly stored after being fully cooled. 

It shall not be exposed to the rain or immersed in water. 

Please store it in the dry and ventilated place. 

IX. Suggestions

The warranty period of this product is one year, and it is suggested to 

use the original accessories. For any fault not caused by using the 

original accessories, it shall be out of the warranty scope. 

*
*

*

*

*
*
*
*
*
*

*

*

*
*

*
*

Notice: The factory set pressure value of the air pump is 10PSI 

(10PSI=0.689BAR), and at the time of the secondary use, the set 

pressure value for the last time use will be displayed by default. 

Notice: After powered on, if there is no operation within 2 minutes, the 

air pump will enter standby mode, and the machine can be initiated 

by pressing the power switch button 

VI. Precautions

The applied power source must be the 12V DC power source (as 

Figure 3). 

Don't block the air inlet (10) at the bottom of the air pump, and 

guarantee air inlet (10) to be always unblocked. 

Observe the local waste treatment provisions, and it is not allowed 

to throw the air pump away randomly. 

Don't use this product when the hose is damaged, and please 

change the hose immediately. 

Don't pull out the hose when inflating, because that the high 

pressure may hurt the physical body.

Don't make the air pump work for more than 15 minutes, because 

that motor overheating may cause internal damage; and  the air 

pump shall be fully cooled for 30 minutes after continuously working 

up to 15 minutes. 

Please don't use this air pump if any part is damaged, and please 

contact with the professional personnel to repair it. 

This product shall not be exposed to the rain or immersed in water. 

In order to prevent risk, the inflation inlet shall not be forward to face 

or body. 

Please don't not leave while inflating.

  

.

MWA632

           

DC12V

MWA632

           

DC12V

*

Please start the car when using the product, in case of unnecessary 

damage.

Summary of Contents for MWA632

Page 1: ...ctions carefully before using this product Please operate in the correct way based on complete understanding Distributed by Electus Distribution Pty Ltd 320 Victoria Rd Rydalmere NSW 2116 Australia www electusdistribution com au Made in China 12VDC 16PSI Air Pump 12VDC 16PSI Air Pump ...

Page 2: ...the box before using it if any missing please contact with the local supplier 12VDC 16PSI Air Pump 12VDC 16PSI Air Pump Air pump Hose Instruction Book 1 I Product Introduction 1 II List of Accessories 1 III Details of Accessories 1 IV Safety Instructions 2 V Inflation Operation 3 4 VI Precautions 4 VII Fault Handling 5 VIII Maintenance and Storage 5 IX Suggestions 5 Inflation inlet Pressure value ...

Page 3: ...product or power source which will damage the product Warning The purpose of using this product is limited to the description in the instruction book Warning Before using please check the cigarette lighter socket to make sure that there is no rust or residue inside The cigarette lighter socket with poor electric conduction may cause overheating of the product or power source which will damage the ...

Page 4: ... original accessories it shall be out of the warranty scope Notice The factory set pressure value of the air pump is 10PSI 10PSI 0 689BAR and at the time of the secondary use the set pressure value for the last time use will be displayed by default Notice After powered on if there is no operation within 2 minutes the air pump will enter standby mode and the machine can be initiated by pressing the...

Reviews: