background image

STEPS TO FOLLOW

8

7101990

BEFORE MOWING

F

Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes.

F

Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade.

F

Fill the fuel tank outside. Clean off spilled fuel.

F

Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with any attachments. Owner’s Manual

instructions are for your safety and the safety of others.

F

Exhaust fumes are dangerous. Start the engine outside.

F

Make sure all safety devices are in place and working correctly.

F

Operation of the mower is only for a person that has experience.

F

Wet grass can be dangerous. Let the grass dry.

F

Instruct children and others to keep away from the work area.

F

Never cut the grass without good light.

F

Pick up loose objects. Remove them from the mowing area.

WHILE MOWING

F

Watch for fixed objects and avoid them. They can damage the mower or cause injury.

F

A hot engine, muffler, and transmission will cause a burn. Do not touch.

F

Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check a slope.

F

Lack of daylight or good artificial light is cause to stop mowing.

F

Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the unit vibrates excessively.

F

Do not make adjustments or repairs without stopping the engine. Disconnect the spark plug wire.

F

On or near roads, watch out for traffic. Direct discharge away from roads.

F

When mowing, avoid areas where traction is unsure. Look back before changing direction of travel.

F

In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass from the mower.

F

Never remove any safety related parts.

F

Do not pour gasoline into a engine that is hot or running.

AFTER MOWING

F

Always let the mower cool before storing in an enclosed area.

F

Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before storing.

F

Tighten all loose nuts, bolts and screws before you use the unit.

F

Empty and clean any grass catcher or other accessory.

F

Remove the key or disconnect the spark plug wire to prevent unauthorized use.

F

Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion.

F

Only original parts or factory approved substitutes can be used to service the mower.

F

When storing the mower for an extended period, remove the fuel from the fuel tank.

F

Instruct children to leave the mower alone. It is not a toy.

F

Never keep gasoline near a source of ignition. Always use an approved container. Keep gasoline away from children.

F

Lubricate according to the Instruction Book. See “Lubrication”.

IMPORTANT-- --Read the Instruction Book. Keep this book for future use and reference.

WARNING: Look for this symbol to point out important
safety precautions. It means: “Attention! Become Alert!
Your Safety Is Involved.”

Not 

for  

Reproduction

Summary of Contents for Clipper 385002 108C Series









































Reviews: