manualshive.com logo in svg

Roto-Mix 420-12, Assembly, Operation And Parts Manual, Page: 25 / 63

Share
Download
Roto-Mix 420-12 Assembly, Operation And Parts Manual Download Page 25

 

25 

SPECIFICATIONS

 

 

 

 

420-12 490-14

 

 

 

   

 

 

Capacity (Cu. ft.) 

420 

490 

 
Top Auger Bearing (Front) 

1-3/4” 2-Bolt 

1-3/4” 2-Bolt 

 
Top Auger Bearing (Rear) 

3” 4-Bolt 

3” 4-Bolt 

 
Bottom Auger Bearing (Front) 

1-3/4” 4-Bolt 

1-3/4” 4-Bolt 

 
Bottom Auger Bearing (Rear) 

3-1/2” 4-Bolt 

3-1/2” 4-Bolt 

 
Rotor Bearing (Front) 

2-15/16” 4-Bolt 

2-15/16” 4-Bolt 

 
Rotor Bearing (Rear) 

4” 4-Bolt 

4” 4-Bolt 

 
Top Auger Sprockets 

80-A-70 

80-A-70 

 100-A-27 

100-A-27 

 

 
Bottom Auger Sprockets 

100-A-54 

100-A-54 

 100-B-13H 

100-B-13H 

 
Rotor Sprocket 

100-D-96 

100-D-96 

 
Drive Sprockets 

80-SK-17H 

80-SK-17H 

 
Top Auger Flighting 

3/8” Steel 

3/8” Steel 

 
Bottom Auger Flighting 

1/2” Steel 

1/2” Steel 

 
Tub Bottom Construction 

1/4” Steel 

1/4” Steel 

 
Auger Bottom Construction 

3/8” Steel 

3/8” Steel 

 
Right Side Sheet Construction 

3/16” Steel 

3/16” Steel 

 
Left Side Sheet Construction 

3/16” Steel 

3/16” Steel 

 
Front End Sheet Construction 

1/4” Steel 

1/4” Steel 

 
Rear End Sheet Construction 

3/16” Steel 

3/16” Steel

 

Summary of Contents for 420-12
































































Reviews:

No comments