manualshive.com logo in svg

Roto-Jet 2200, Disassembly-Assembly Manual, Page: 3 / 41

Share
Download
Roto-Jet 2200 Disassembly-Assembly Manual Download Page 3

ROTO-JET PUMP

 

DISASSEMBLY/ASSEMBLY 

Model 2200 

Table of Contents 

 

ii 

4.4.

 

ROTOR

 

ASSEMBLY

 

INSTALLATION ....................................................................... 24

 

4.5.

 

SEAL

 

INSTALLATION ............................................................................................... 24

 

4.5.1.

 

2-7/8” Type S Single Seal .................................................................................. 24

 

4.5.2.

 

3-1/2” Type SD Single/Double Seal ................................................................... 25

 

4.5.3.

 

Seal Hub Replacement (

Reference Figure 2-9

) – 3-1/2” Seal Only ................... 26

 

4.6.

 

PICK-UP

 

TUBE

 

AND

 

MANIFOLD

 

INSTALLATION .................................................... 26

 

5.

 

ROTATING COMPONENT REPLACEMENT ................................................................... 29

 

5.1.

 

ROTOR

 

REMOVAL ................................................................................................... 29

 

5.2.

 

ROTOR

 

INSTALLATION ........................................................................................... 29

 

6.

 

HYDROSTATIC PRESSURE TEST ................................................................................. 29

 

7.

 

BALANCING (ROTOR ASSEMBLY) ................................................................................ 29

 

8.

 

PARTS ............................................................................................................................. 30

 

8.1.

 

SPARE

 

PARTS ......................................................................................................... 30

 

8.2.

 

ORDERING

 

PARTS .................................................................................................. 32

 

9.

 

MAINTENANCE RECORD ............................................................................................... 33

 

APPENDIX A ........................................................................................................................... 34

 

APPENDIX B ........................................................................................................................... 36

 

 

Summary of Contents for 2200










































Reviews:

No comments