Rotex RoCon M1 Operating Instructions Manual Download Page 21

x

 Operation

FA ROTEX RoCon mb • 09/2017

21

3.6

Special system settings

The RoCon mb controller is already basically configured for the 
ROTEX HPSU monobloc compact. However, it must still be 
adapted to optionally connected accessories and the installation 
environment during initial commissioning.

The adjustment is carried out by setting the parameters in the 

"Configuration"

 rotary switch setting 

.

The next lowest level can be accessed or the respective pa-
rameter directly accessed by navigation with the rotary button.

3.6.1 Access rights (technician code)

Certain settings in the control unit are limited by access rights. To 
receive access to these parameters, the technician code must be 
entered at the 

"Setup"

 level.

Fig. 3-13 shows the basic procedure for entering the access 
code. The expert company receives the technician code in a sep-
arate letter.

3.6.2 Heat slope

The heat slope is used to adjust the target feed temperature to 
the characteristics of the building depending on the respective 
outside temperature (weather-dependent T-HS control, see 
chap. 3.6.4). Generally speaking, the steepness of the heating 
slope describes the ratio of the T-HS change to the external tem-
perature change.

The heat slope is valid within the limits of the minimum and 
maximum temperatures set for the respective heating circuit. De-
viations may occur between the room temperature measured in 
the occupied area and the desired room temperature; these can 
be minimised by installing a room station or a room thermostat.

The 

control unit

 is set at the 

factory

 in such a way that the 

heat 

slope

 does 

not independently adjust itself

 during operation.

Automatic heat slope adaptation

 can be activated (parameter 

[HC Adaption]), 

if

 the 

room station 

(RoCon U1, 

 15 70 34) is 

connected

 (see chap. 3.6.4).

Start conditions for automatic heat slope adjustment:
– Outside temperature < 8 °C
– Operating mode is automatic (I or II)
– Duration of the setback period is at least 6 h

If 

no automatic heat slope adjustment

 is activated, the heat 

slope can be 

manually

 adjusted by 

adjusting

 the 

[Heat-Slope] 

parameter

).

Fig. 3-13 Entering the access code

Configuration

Setup

System Configuration

Access Rights

User

Access Rights

Expert

Setup

Language

Date

Setup

Keylock Function

Access Rights

Outdoor type

Access Rights

Access Rights

Access Rights

Caution - Risk of overheating of floor 
heating!

In the event of malfunction or during manual 
operation, the floor heating, the screed or the 
floor structure could be damaged due to over-
heating.

Prior to initial commissioning of the floor 
heating system, set the maximum temper-
ature limit in the RoCon mb controller 
(parameter [T vbh1 max]) and the maximum 
permissible system temperature (parameter 
[Max T-Flow]).

Connect an overheating protection switch (in 
the building) at the "EXT" plug connection to 
external operating mode switch-over so that 
the ROTEX HPSU monobloc compact is 
switched to "Standby" or "Summer" operating 
mode (see chap. 3.4.2).
With parameter [Room thermostat] = On or 
parameter [Interlink fct] = On, the overheating 
protection switch must be connected so that 
the room thermostat's switching contact is 
interrupted.

If the floor heating is also used for room 
cooling, the connection notes in the above 
point also apply to the connection of a 
moisture protection switch in the building.

Summary of Contents for RoCon M1

































































Reviews: