Rotex R2CND028A4AA Operation Manual Download Page 6

3 Operation

Operation manual

6

R0 R035A4AA

Wall-mounted condensing boiler

3P469438-6D – 2017.07

To change the domestic hot water setpoint

1

Turn  the  right  dial  while  you  are  at  the  home  screen.  The
setpoint  screen  will  appear  as  shown  below  and  the  setpoint
can  be  adjusted  by  turning  the  right  dial. 

Note: 

The    icon

means you are at the setpoint screen.

2

To apply changes done, wait for 3 seconds or press the "Enter"
button. Pressing the "Cancel" button cancels the changes done.

NOTICE

To  be  able  to  change  the  setpoint  of  central  heating  or
domestic  hot  water,  the  corresponding  operation  mode
must  be  enabled.  If  it  is  not,  the  related  dial  has  no
function.

3.3.5

Possible central heating operation modes

Mode

Description

Boiler only

The case that the system only
contains the boiler. No room
thermostat or outdoor sensor are
connected. The central heating water
temperature setpoint is displayed. The
setpoint can be adjusted with the left
dial.

The   icon is shown on the screen
when the central heating operation
mode is enabled.

Combination with ROTEX
Opentherm room
thermostat (DOTT )

The case that ROTEX Opentherm
room thermostat is connected to the
boiler. Room temperature setpoint is
displayed. The room temperature
setpoint can be adjusted from the user
interface by means of the left dial or
from the ROTEX room thermostat.

The   icon is shown on the screen
instead of the   icon when central
heating operation mode is enabled.

Mode

Description

outdoor sensor
(Weather compensation)

The case that outdoor sensor is
connected to the boiler. In this case,
the central heating water temperature
is regulated according to the outdoor
temperature. The virtual room
temperature setpoint is diplayed. The
virtual room temperature setpoint can
be adjusted by means of left dial.
Increasing or decreasing the setpoint
value reflects to the central heating
water temperature and the room
temperature, respectively.

The   and   icons are shown on the
screen when central heating operation
mode is enabled.

NOTICE

To enable weather compensation, the heating slope value
must  be  higher  than  "5"  (see 

"User  settings  menu:

Parameters (short)" on page 8

).

INFORMATION

If  an  outdoor  sensor  is  connected  to  the  boiler  together
with  an  Opentherm  room  thermostat  (whether  DOTT  or
not),  the  rules  of  the  case  "Combination  with  Opentherm
room  thermostat"  are  applicable.  The  outdoor  sensor  only
provides outdoor temperature data to the room thermostat
for water temperature calculation.

3.3.6

About the central heating ECO mode

The  central  heating  ECO  mode  provides  more  economic  central
heating.  Main  purpose  of  the  ECO  mode  is  to  operate  the  boiler  at
the  condensing  temperature  range  so  to  increase  the  efficiency.
ECO mode can be activated at any central heating operation mode
explained above.

ECO mode can be enabled from the user settings menu (see 

"User

settings menu: Parameters (short)" on page 8

).

INFORMATION

ECO  mode  is  only  for  central  heating,  it  has  no  effect  to
domestic water heating.

When central heating ECO mode is enabled,   icon is shown on the
screen while the central heating operation mode is enabled.

3.3.7

About the domestic hot water operation

This  unit  supplies  domestic  hot  water  by  way  of  a  plate  heat
exchanger  (instantaneous)  or  by  way  of  a  hot  water  storage  tank
according to model of the boiler.

If  the  boiler  is  instantaneous  type,  domestic  hot  water  operation  is
activated  when  water  is  being  tapped.  Water  flow  rate  must  be  at
least 2.5 l/min.

If  it  is  storage  tank  type,  domestic  hot  water  operation  is  activated
according to storage tank temperature value.

The   icon blinks when domestic hot water operation is active.

INFORMATION

Domestic  hot  water  operation  mode  must  be  enabled  for
the  boiler  to  be  able  to  produce  domestic  hot  water.  (i.e.
summer mode or winter mode).

Summary of Contents for R2CND028A4AA













Reviews: