11. TIMING CHART OF EVENTS
1. After mounting, setting parameters and applying power, walk test unit to
verify detection area.
2. If the door does not operate properly, recheck the dip switch settings and
pattern adjustments.
3. After rechecking, if there is still a problem, adjust the sensitivity.
10. VERIFICATION OF OPERATION
13. TROUBLESHOOTING
Compiler
of
Technical
File
(EC
Community)
David
Morgan
Hotron
Ireland
Ltd
26
Dublin
Street,
Carlow,
Ireland
Ph:
+353-(0)59-9140345
Fax:
+353-(0)59-9140543
Description
of
Product:
HR94D1-C1 is designed to monitor the side screen of the automatic door.
Technology used is Active Infrared Technology
Directives
Fulfilled:
DIRECTIVE 2006/42/EC
DIN 18650-1:2005 Powered pedestrian doors Part 1: Product requirements chapter 5.7.4
EN12978:2003 Industrial, commercial and garage doors and gates - safety devices for power operated doors and gates - Requirements and test methods.
EN62061:2005 Functional safety of electrical/electronic/programmable electronic safety-related systems.
EN ISO 13849-1:2008 Safety of machinery - Safety-related parts of control systems.
EN 16005:2012
EC type examination 44 205 12 414283-001
Above
EC
Type
Directives Certified
by:
TUV
NORD
CERT
GmbH
30519
Hannover,
Germany
Identification
No:
0044
Harmonized
Standards
Used:
EN
ISO
13849-1:2008
Other
Technical
Standards
Used:
DIN 18650-1:2005,
EN16005:2012
Declaration
made
by
Kaoru
Musya
General
Manager. Honda
Electron
Date
9
th
of
Nov
2012
Location
of
Declaration
Honda
Electron
Co.,
LTD.
1-23-19
Asahi-Cho,
Machida-City,
Tokyo,
Japan
14. HR94D1-C1 EC DECLARATION OF CONFORMITY
<
Disclaimer
>
The
manufacturer
cannot
be
held
responsible
for
below.
1. Misinterpretation
of
the
installation
instructions,
miss
connection,
negligence,
sensor
modification
and
inappropriate
installation.
2. Damage
caused
by
inappropriate
transportation.
3. Accidents
or
damages
caused
by
fire,
pollution,
abnormal
voltage,
earthquake,
thunderstorm,
wind,
floods
and
other
acts
of
providence.
4. Losses
of
business
profits,
business
interruptions,
business
information
losses
and
other
financial
losses
caused
by
using
the
sensor
or
malfunction
of
the
sensor.
5. Amount
of
compensation
beyond
selling
price
in
all
cases.
Sensitivity
High
» Adjust high (clockwise) to increase sensitivity.
» Adjust low (counter-clockwise) to decrease sensitivity.
CAUTION
!
As the detection area is variable depending on clothes, floor material and sensitivity adjustment,
please confirm that the detection area demanded in EN16005 is secured after adjustment.
NON-
DETECTION
DETECTION
Test Input
NON-TEST
TEST
Sensor
Sensor
Supplying DC12 to 24V, make current flow
from Gray to Brown.
Break the current
flow on test state.
NON-
DETECTION
Yellow
Blue
DETECTION as
response to TEST
NON-
DETECTION
NON-TEST
TEST RESPONSE
T1
T2
POWER
OFF
Brown
Gray
Brown
Gray
Yellow
Blue
Yellow
Blue
Yellow
Blue
Sensor
Brown
Gray
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Yellow
Blue
Dip Switch
#6:N.C.
Dip Switch
#6:N.O.
T1:
8~14
[mSec] App.
T
2: 9~15
[mSec]App.
12. SELF DIAGNOSTICS ERRORS
When the sensor has the self-test error, the green/red LED blinks alternately.
The blinking cycle is different, according to the kinds of the error as follows.
LED
Cause
Solution
Output on Error State
Response to TEST
DIP
Switch
#6 : N.O.
DIP
Switch
#6 : N.C.
No Response
Internal error
Low reflection
level
Please replace the sensor.
Set the sensitivity to maximum,
and then reactivate the sensor.
If the error continues, set
DIP Switch #7
“
ON
”
.
■
Fast Blink
■
Slow Blink
Green
Red
Green
Red
Green
Red
■
Slow Blink
Test line
disconnection
( Green/Red )
( Red/Red/Green )
( Green/Red )
Please confirm the connection
of the test line.
Sensor does not
operate
Sensor intermittently detects
Sensor detects without
obvious reason
Sensor Connector
Sensor is very dusty or
covered in water drops, etc.
Power Supply
Detection pattern in the wrong position
Detection pattern too far in front of the door, detecting
people passing by
Sensitivity too low
Sensor detects the door movement
Sensitivity too high
Another sensor is too close by
There is a cloth mat in the monitored area.
The condition of the monitored area is
varying.
･
Dusty / Dirty
･
Snow
The condition of the monitored area can change due to heavy dust or dirty,
heavy snow or
footprints being left in fresh snow, this will cause the malfunction sometimes. Set the “Presence Timer” to
a short times.
Refer to Section 7.
Adjust the detection pattern - move it closer to the door
Reactivate the sensor and wait for 10 seconds.
If the indicator LED is an Orange color, adjust the pattern depth angle away from the door
Change the frequency to each sensor.
Turn down Sensitivity.
Alter the detection pattern by changing sensor angle, and/or pattern width adjustments
Turn up sensitivity
Clean the sensor (do not use thinner or alcohol to clean sensor)
Check that the power supply is properly connected.
Tighten connector or reconnect
Internal error
(Green/Red LED blinks alternately)
Low reflection error or Test line disconnection
(Refer to Section 7, Section 12)
Slow blink
Fast blink
Please replace the sensor (Refer to Section 12)
Problems
Possible Cause
Solution
The door kept open,although there is
no object in the detection area.
Yellow
Blue
Yellow
Blue
For More Information - Tel:
+61 7 3205 1123
Email:
Web:
www.rotech.com.au
