HR94D1-C1
User Manual (Original)
Cover
50mm
③
Fasten unit with mounting screws rovided.
①
Drill mounting (3.5mm
φ
) a n d
wiring (10mm
φ
) holes.
Sensor
’
s
Cable
Cable
Red
Black
Yellow
Brown
AC/DC
12 to 24 [V]
±10%
Output
Collector
Emitter
Power
（
Non
Pole
）
Test Input
Test-P
Test-N
COMPLIED
STANDARDS
DIN18650-1:2005
EN 12978:2003
EN 16005:2012
EC type examination
44 205 12 414283-001
English
Green
Standby
Red
Detecting
Orange
The detection
area is too close to the door
Green/Red
Internal
Sensor Error
blinking alternately
Installation
Instruction
Accessories
Mounting
Template
Cable
Mounting
Screws
(2
pcs.)
1. DESCRIPTION
☆
= Default Setting
Output logic is defined by this switch.
In the N.C. , Opto-Coupler will be driven in the state of non-
detection.
2. DIMENSIONS
3. LED INDICATORS
5. TECHNICAL SPECIFICATIONS
6. MOUNTING & WIRING INFORMATION
7. DIP SWITCH SETTINGS
Description
The HR94D1-C1 will detect a stationary object only for the time period
set by the Presence Timer. The timer will reset and begin if any
movement is detected.
Possible Setting Options
Function
Presence
Timer
Output
ON
Dip Switch X
Disregarding this
symbol may result in
serious injury or death
Note
Special attention is required
when this symbol is shown
②
Remove cover using
a coin.
Drilling
may
cause
electric
shock.
Be careful of hidden
wires
inside
the
door
engine cover.
Setting required to conform with
EN16005:2012
④-1
Wiring to a door controller that can
test the sensor.
1 2
3 4
5 6
7 8
WARNING
!
CAUTION
!
Disregarding this symbol may
result in injury or damage to
equipment
3m
(9.8ft)
A
B
Mounting height of 3 m
(9.8ft) or lower
Ensure there are no moving
objects in the detection zone
Use different frequency settings
for sensors in close proximity
Ensure the minimum of
reflected sunlight from the
floor
4. MOUNTING PRECAUTIONS
Ensure
no condensation gets
onto the sensor.
If
possible
ensure
no
accumulation of snow or
water on the floor.
If the sensor is exposed to
excessive rain install with a
Hotron weather cover
WARNING
!
⑦
7. Place cover on sensor and clean the sensor.
⑥
Set desired sensor parameters as noted
in Sections 7 & 8.
CAUTION
!
Blue(-)
Gray
2s
☆
1
2
30s
1
2
1
2
1
2
60s
∞
N.C.
☆
6
Set the timer to 30sec. or more to comply with EN16005
When more than two sensors are used in close
proximity to each other, select different frequency setting for each
sensors to prevent interference.
( A + B + C + D = Maximum 4 sensors )
7
8.DETECTION AREA WIDTH AND DEPTH ADJUSTMENT
Detection Area Depth Adjustment
Detection Area Width Adjustment
0.190kg, ( 0.42lbs.)
Cable : 2.5m (8ft.) Mounting Screw (2pcs)
Mounting Template User Manual
-20
to
+60
[Deg.C],(-4
to
140
Deg.F)
Below 80%
Model
Name
HR94D1-C1
Active
Infrared
Detection
Installation
Height
3[m]
(9.8[ft])
Max
Detection
Method
Approx 0.5s
Output
Holding
Time
Presence
Timer
0.1s
～
0.2s
Output
Weight
Accessories
Test
Input
Operating
Temperature
Operating humidity
Response
Time
Supply Voltage
AC/DC 12 to 24 [V] ±10% Red & Black (Nonpole)
Power
Consumption
AC12V-1.8
[VA]
(Max)
AC24V-2.8 [VA] (Max)
DC12V-100
[mA]
(Max)
DC24V-60
[mA]
(Max)
Category
2 , performance level C for presence detection according to EN ISO
13849-1:2008
IP
Rate
IP54
Notice:
Specification
may
be
changed
without
prior
notice.
N.O.
N.C.
☆
DIP Switch
Potentiometer
(Sensitivity Volume)
Area Mask
Connector
Mounting Holes
DIP Switch #1, #2 (2, 30, 60,
∞
seconds)
Open collector 7.5[mA](Max) Resistor Load
DIP SW
#6 : N.C.
DIP SW
#6 : N.O.
Normally Drive (Normally Close)
Open on Detection
Normally Open
Drive on Detection (Close on Detection)
Opto coupler(NPN) Voltage:55 [VDC] Max. Current:50 [mA] Max.
Dark Current : 100 [nA] Max. (Resistance load)
Non-Test : DC12 to 24 V / Test : Open
6 [mA] Max.@ 24 [VDC]
⑤
House connectors in the space provided.
Section 7. DIP Switch Settings
Section
8. Detection Area Width andDepth Adjustment
Frequency
» The body of the sensor can be rotated from 0º~5º(3 Steps)
MAX
Max Area
Min Area
2.5m 2.0m 1.5m 1.0m 0.5m 0m
2.5m 2.0m 1.5m 1.0m 0.5m 0m
MIN
0
0.5m
1.6'
1.0m
3.3'
1.5m
4.9'
2.0m
6.6'
2.5m
8.2'
3.0m
9.9'
8.2' 6.6' 4.9' 3.3' 1.6' 0'
8.2' 6.6' 4.9' 3.3' 1.6' 0'
SIDE VIEW/DETECTION AREA
FRONTAL VIEW/DETECTION AREA
NARROW
WIDE
Area Mask
Adjustment
(m)
0.5m
1.0m
1.5m
2.0m
4.9'
3.3'
1.6'
6.6'
0
2.5m
8.2'
3.0m
9.9'
4.9'
3.3'
1.6'
4.9'
3.3'
1.6'
6.6'
6.6'
0.5
1.0
1.5
0.5
1.0
1.5
2.0
2.0
4.9' 3.3' 1.6'
4.9'
3.3'
1.6'
6.6'
6.6'
0.5
1.0
1.5
0.5
1.0
1.5
2.0
2.0
9. APPLYING POWER
CAUTION
!
BEFORE APPLYING POWER, READ AND FOLLOW THESE INSTRUCTIONS:
When power is applied, the sensor will read and store the environmental optical parameters.
This is necessary for Presence Detection to work properly.
①
CLEAR THE AREA OF ANY UNNECESSARY OBJECTS.
②
APPLY POWER.
③
WALK AWAY FROM THE DETECTION AREA immediately.
④
DO NOT ENTER DETECTION AREA for 10 SECONDS while the “learning procedure” for Presence detection is carried out.
If the sensor can see moving objects during the "learning procedure", the sensor will not proceed to presence detection.
Please DISCONNECT POWER TO THE SENSOR, when carrying out the following work.
AFTER THE TASK, APPLY POWER AGAIN.
1. When the floor condition is changed; for example with the addition of of woolen or rubber mat.
2. Adjusting pattern or sensitivity.
(Drive)
Indicator LED
75mm(2.96")
65mm
(2
.56")
30mm
(1.18")
35mm
(1.38")
40mm
(1.57")
15mm
(0.59")
20mm
(0.79")
5mm
(0.20")
210mm(8.27" )
Φ
10mm(0.39")
-Wiring hole
EN16005
EN16005
[ 0
degree ]
setting
[ 5
degree ]
setting
Reflection
Diagnostics
Normal
☆
7
A low reflected infrared signal is indicated by a slow flashing Red/Green
LED.
To ignore this low reflection error state, set this dip switch to “Low
Reflection”(ON).
To comply with EN16005 set to “Normal”
EN16005
Receiver
IR Spot
Transmitter
LED
Low
Ref.
7
7
Normal
☆
Transmitter
Receiver
IR Spot
Monitor
Mode
Set to snow in instances where false door activations can result from
blowing snow, leaves or rubbish in the door close area.
5
Normal
☆
Snow
5
5
Normal
☆
☆
30s
6
When connected to a door controller without a TEST input, set to “OFF”.
When connected to a door controller with a TEST input, set to “ON”
Refer to [11.Timing Chart of events].
Test Input
Setting
from Door
Controller
Set to “ON” to comply with EN16005
OFF
ON
☆
8
8
OFF
☆
0v
ON
Without TEST
With TEST
Without TEST
0v
OFF
1
2
A
☆
3
4
A
☆
3
4
B
3
4
3
4
3
4
C
D
EN16005
8
ON
Set to “ON” to comply with EN16005
EN16005
④ -2
Wiring to a door controller that
cannot
test the sensor.
Sensor
’
s
Cable
Cable
Red
Black
Yellow
Brown
AC/DC
12 to 24 [V]
±10%
Output
Collector
Emitter
Power
（
Non
Pole
）
Blue(-)
Gray
OFF
do not connect
do not connect
8
The above illustrated detection areas represent the actual position of the infrared beams. The actual detection area observed will vary depending on the
sensor installation environment, object
been
detected
and
sensor
settings.
Please ensure that the detection area is set to conform to EN16005.
CAUTION
!
Rotech Group Pty Ltd
